manualshive.com logo in svg

LG MS2548GR, Руководство по обслуживанию

Поделиться
Скачать
LG MS2548GR Скачать руководство пользователя страница 25

5-15

CONDITION

CHECK

RESULT

CAUSE

REMEDY

No microwave
oscillation.

No continuity.

Continuity.

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 2 and
check continuity
of relay2.
(Operate the unit)

Abnormal

Defective high
voltage
transformer.

Replace high
voltage
transformer.

Check high vol-
tage transformer.

Abnormal

Normal

Defective circuit
protector.

Replace circuit
protector.

Check circuit
protector.

Abnormal

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Check high vol-
tage capacitor.

Normal

Abnormal

Defective high
voltage diode.

Replace high
voltage diode.

Check high vol-
tage diode.

Normal

Abnormal

Defective
magnetron.

Replace
magnetron.

Check
magnetron.

Normal

(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run.

(Display operates properly)

LGE Internal Use Only

Copyright © 2007 LG Electronics. Inc. All right reserved. 
Only for training and service purposes

Содержание MS2548GR



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды