manualshive.com logo in svg

LG MS2548GR, Руководство по обслуживанию

Поделиться
Скачать
LG MS2548GR Скачать руководство пользователя страница 16

K. PCB ASSEMBLY REMOVAL

1) Remove the control panel assembly from the

cavity. (Refer to control panel assembly removal
on previous page.)

2) Remove screws which hold the PCB SUB ASS’Y to

the control panel.

3) Disconnect the flat cable from the PCB SUB

ASS’Y and take off the PCB SUB ASS’Y.

L. INTERLOCK SYSTEM

1) INTERLOCK MECHANISM

The door lock mechanism is a device which has
been specially designed to eliminate completely
microwave activity when the door is opened during
cooking and thus to prevent the danger resulting
from the microwave leakage.

2) MOUNTING OF THE PRIMARY/MONITOR

SECONDARY SWITCHES TO THE LATCH BOARD.

3) INSTALLATION AND ADJUSTMENT OF THE

LATCH BOARD TO THE OVEN ASSEMBLY

• Mount the latch board to the oven assembly.
• Adjust the latch board in the arrow direction so that

oven door will not have any play in it when the door
is closed.

• Tighten the mounting screw.
• 

Check for play in the door by pushing the door
release button. Door movement should be les
than 0.5 mm. (1/64 inch)

Don't push the door release button while making
adjustment. Make sure that the latch moves
smoothly after adjustment are completed and that
the screws are tight. Make sure the primary, monitor,
and secondary switches operate properly by
following the continuity test procedure.

5-6

PRIMARY
SWITCH

ADJUSTMENT
DIRECTION

MONITOR
SWITCH

SECONDARY
SWITCH

CAUTION: CHECK THE CORRECT POSITION

MAGNETRON

H.V. TRANSFORMER

PRIMARY

CIRCUIT PROTECTOR

H.V. CAPACITOR

H.V.
DIODE

FIG. 1

LGE Internal Use Only

Copyright © 2007 LG Electronics. Inc. All right reserved. 
Only for training and service purposes

Содержание MS2548GR



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды