LG MS1949G Скачать руководство пользователя страница 25

Страница: 25 / 35

5-15

(TROUBLE 3) Display shows all figures set, but oven does not start cooking while

desired program times are set and START pad is touched.

(TROUBLE 4) Oven seems to be operation but little heat is produced in oven load.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1.Setting time does

not count down
when touching
START pad.

2. Fan motor or

oven lamp
do not turn
on.

No continuity.

continuity.

No continuity.

Continuity.

Check the con-
nection between
connector and
P.C.B assembly.

Defective
secondary switch.

Replace
secondary switch.

Defective P.C.B
assembly.

Replace P.C.B
assembly.

Check continuity
of secondary
switch (with
door closed).

Check fan motor.

Check oven lamp.

Abnormal.

Normal.

Defective fan
motor.

Defective oven
lamp.

Replace fan
motor.

Replace oven
lamp.

Loose connection.

Connection then
tightly.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

Output is low.

Lower than 90% of
rating voltage.

Normal.

Abnormal.

Measure the
output power.

Disconnect the
wire leads from
relay 2 and check
on and off time
with multitester.

Defective P.C.B
assembly.

Replace P.C.B
assembly.

Decrease in power
source voltage
with load.

Suggest customer
contact local
electric power
utility co. or
qualified
electrician.

Check the
power source
voltage.

Defective
magnetron.

Replace
magnetron.

NOTE: Simple test of power output-conducted by heating one liter water for one min. if available.

Minimum 8.5

C temperature rise is normal condition.

LGE Internal Use Only

Содержание MS1949G



































Результаты поиска

Содержание MS1949G

Отзывы:

Похожие инструкции для MS1949G

Бренды по названию

Популярные бренды

LG MS1949G, Руководство по обслуживанию

Результаты поиска

Содержание MS1949G

Отзывы:

Похожие инструкции для MS1949G

Бренды по названию

Популярные бренды