LG MS1949G Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 35

background image

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

Approx.: 1.4 ohm
Approx.: 90 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

PRIMARY
TERMINAL

SECONDARY
WINDING

FILAMENT
WINDING
TERMINAL

COMPONENT TEST PROCEDURE

LGE Internal Use Only

Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes

«
...
16
17
18
19
20
...
»

Содержание MS1949G




































Отзывы:

Нет отзывов

Похожие инструкции для MS1949G

Бренд: GE Страницы: 36

Бренд: GE Страницы: 2

Бренд: GE Страницы: 36

Бренд: GE Страницы: 28

Бренд: GE Страницы: 24

Бренд: GE Страницы: 24

Бренд: GE Страницы: 44

Бренд: GE Страницы: 3

Бренд: GE Страницы: 40

Бренд: Atag Страницы: 76

Бренд: GE Страницы: 32

Бренд: Zigmund & Shtain Страницы: 32

Бренд: Magic Chef Страницы: 31

Бренд: Omega Страницы: 20

Built-In Electric 30" Single and Double Ovens

Бренд: Viking Range Страницы: 26

Бренд: san ignacio Страницы: 24

Бренд: Dawlance Страницы: 9

Бренд: Gaggenau Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды