LG MS09AQ Скачать руководство пользователя страница 1

Страница: 1 / 17

P/NO : MFL67855410

INSTALLATION MANUAL

AIR

CONDITIONER

www.lg.com

Please read this installation manual completely before installing the product.

Installation work must be performed in accordance with the national wiring

standards by authorized personnel only.

Please retain this installation manual for future reference after reading it thoroughly.

This product contains Fluorinated Greenhouse Gases. (R410A)

[Representative] LG Electronics Inc. EU Representative : LG Electronics European Shared Service Center B.V.

Krijgsman 1, 1186 DM Amstelveen, The Netherlands

[Manufacturer] LG Electronics Inc. Changwon 2nd factory 84, Wanam-ro, Seongsan-gu, Changwon-si,

Gyeongsangnam-do, KOREA

For more information, Refer to the CD or LG Web site (www.lg.com).

WALL MOUNTED

Original instruction

LIS

LIA

ΕΛ

ΛΗ

ΙΚ

TIN

LIM

MÂ

Содержание MS09AQ


















Результаты поиска

Содержание MS09AQ

Отзывы:

Похожие инструкции для MS09AQ

Бренды по названию

Популярные бренды

LG MS09AQ, Руководство по установке

Результаты поиска

Содержание MS09AQ

Отзывы:

Похожие инструкции для MS09AQ

Бренды по названию

Популярные бренды