manualshive.com logo in svg

LG MS-197W, Руководство по обслуживанию

Поделиться
Скачать
LG MS-197W Скачать руководство пользователя страница 14

D. DOOR GROSS ASSEMBLY REMOVAL

1) Open the door.
2) Pull out the door protector very carefully with a    flat-

blade screwdriver.

CAUTION : Be careful not to damage door seal plate

by screwdriver.

3) Lift up and push the door.

NOTE:
1. After replacing the door, be sure to check that the

primary switch, monitor switch, and secondary switch
operate normally.

2. After replacing the door, check for microwave energy

leakage with a survey meter. Microwave energy must
be below the limit of 5 mW/cm. (with a 275 ml water
load)

3. When mounting the door assembly to the oven

assembly, be sure to adjust the door assembly parallel
to the chassis. Also adjust so the door has no play
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven.

E. HIGH VOLTAGE TRANSFORMER 

REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from magnetron, high voltage

transformer, and capacitor.

3) Remove the screw holding the high voltage

transformer to the baseplate.

F. FAN MOTOR ASSEMBLY REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, noise filter

and high voltage capacitor.

3) Remove the two screws holding the the suction guide

ASS’Y to the oven cavity and remove the high voltage
diode earth screw.

4) Remove the screw of the capacitor bracket.
5) Remove the two screws holding the fan motor ASS’Y

to the suction guide ASS’Y.

G. HIGH VOLTAGE CAPACITOR AND

DIODE REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, noise filter

and high voltage capacitor.

3) Remove the screw holding the suction guide ASS’Y to

the oven cavity and remove the high voltage diode
earth screw.

4) Remove the screw holding the high voltage capacitor

bracket.

5-4

Remove Hinge Plate

Remove Door Assembly

Suction
Guide

Fan Motor 
ASS’Y

H.V.
Transformer

H.V.
Diode

H.V.
Capacitor

H.V.
Cable

Содержание MS-197W






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды