LG MFL40910614 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 35

background image

Installation Manual

17

ENGLISH

Wiring Connection

Terminals on the
Outdoor unit

POWER INPUT

(208~230V)

L1

L2

• Connect the wires to the terminals on the control board individually according to the outdoor unit connection.
• Ensure that the color of the wires of outdoor unit and the terminal No. are the same as those of

indoor unit respectively

Precautions when laying power wiring

Use round pressure terminals for connections to the power terminal block.

When none are available, follow the instructions below.
• Do not connect wiring of different thicknesses to the power terminal block. (Slack in the power

wiring may cause abnormal heat.)

• When connecting wiring which is the same thickness, do as shown in the figure below.

Connecting Cables between Indoor Unit and Outdoor Unit

W

ARNING:

Make sure that the screws of the terminal are free from looseness.

Round pressure terminal

Power wire

RECOMMENDATION: The power cord
connected to the outdoor unit should be comply
with the following specifications: ETL
recognized and CSA certified.

GN/YL

Line voltage
(208/230V)

AWG10

GN/YL

AWG18

RECOMMENDATION: When using the separate wires as the power cord, please
secure the separate wires into the control box panel using tie wraps to hold all
wires together in place.

The power connecting cable connected to the indoor
and outdoor unit should be comply with the
following specifications: ETL recognized and CSA
certified.

«
...
15
16
17
18
19
...
»

Содержание MFL40910614




































Отзывы:

Нет отзывов

Похожие инструкции для MFL40910614

Бренд: Zibro Страницы: 2

Бренд: Panasonic Страницы: 76

Бренд: Panasonic Страницы: 118

Бренд: Samsung Страницы: 40

Бренд: aldes Страницы: 4

Бренд: XPower Страницы: 20

GPC 14 SEER R-410A

Бренд: Goodman Страницы: 26

Viroxid HABITAT 3 AIR 160

Бренд: IDS Страницы: 28

Бренд: Fedders Страницы: 24

Бренд: Carrier Страницы: 48

Бренд: Amana Страницы: 32

Бренд: Daikin Страницы: 30

Бренд: Sea Breeze Страницы: 36

Бренд: ECG Страницы: 76

Бренд: Frico Страницы: 9

Бренд: Danby Страницы: 20

Dual DC Inverter (4,1 kW)

Бренд: MAXA Страницы: 43

Бренд: Inverter Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды