LG MFL40910614 Скачать руководство пользователя | Manualshive

Страница: 13 / 35

background image

Remote controller installation

Installation Manual

13

ENGLISH

Installation of Wired Remote Controller(Cassette type)

1. Connect the wired remote controller cable

to the wired remote controller installation
board as shown in the right picture.

2. After fixing the cable to the guide slot,

attach the wired remote controller
installation board at the desired location.

• Before fixing the wired remote controller cable

to the guide slot, remove any clogged part of
the case in the direction to install before the
installation.

3. After locating the wired remote

controller installation board at the
desired location, screw the unit firmly.
(When there is a buried box, install the
wired remote controller board to fit the
buried box.)

• Use the screw provided.

4. After fixing the top part of the wired

remote controller to the installation
board as shown in beside picture, press
the bottom part to assemble the
controller to it’s board.

When disassemble the wired remote controller
from the installation board, use the driver as
shown in the right picture and insert it into the
hole with the arrow. And when you pull the driver
in the front direction, the wired remote controller
will be separated.

12V

Red wire

SIG

Yellow wire

GND

Black wire

❊

The wired remote controller cable is connected as factory default.

12V SIG GND

Red
Yellow
Black

Remote Controller
Cable

Guide slot

Fixate the remote
controller cable
to the guide slot.

Use the screws
for fixate the unit
firmly on the wall.

Installation board

<Front side of

installation board>

<Rear side of

installation board>

Top

Bottom

Wall

Side

Wall

Side

Wall

Side

Wall

Side

Wall

Side

«
...
11
12
13
14
15
...
»

Содержание MFL40910614




































Отзывы:

Нет отзывов

Похожие инструкции для MFL40910614

Бренд: Samsung Страницы: 52

Бренд: Jet Страницы: 11

Бренд: Jet Страницы: 10

Бренд: Kaden Страницы: 16

Бренд: Kaden Страницы: 16

Бренд: Kaden Страницы: 32

Бренд: Kaden Страницы: 24

Бренд: Samsung Страницы: 14

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 43

Бренд: Samsung Страницы: 26

Бренд: Samsung Страницы: 34

Бренд: Samsung Страницы: 26

Бренд: Samsung Страницы: 36

Бренд: Samsung Страницы: 26

Бренд: Samsung Страницы: 40

Бренд: Samsung Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды