LG MC-807WR Скачать руководство пользователя | Manualshive

Страница: 24 / 38

background image

1. Incomplete segments.

• Segment missing.
• Partial segment missing.
• Digit flickering (NOTE: Slight flickering is normal.)

2. Colon does not turn on or blink.
3. A distinct change in the brightness of one or more numbers in display.
4. One or more digits in the display are not lighting.
5. Display indicates a number different from one touched, for example, key in

5

and

3

appears in the display.

6. Specific numbers (for example 7 or 9) will not display when key pad is touched.
7. Display does not count down with time blinking or up with clock operation.
8. Display obviously jumps in time while counting down.
9. Display counts down too fast while cooking.

10. Each indicator light does not turn on after setting cooking cycle.
11. Display time of day does not reappear when cooking is finished.
12. Beep sound is not heard when correct key is touched.

5-14

(TROUBLE 1) The following visual conditions indicate a probable defective control circuit.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Some inputs

cannot be
programmed.

Everything works
as specified.

Still have trouble.

Defective key
membrane
assembly.

Defective PCB
assembly..

Replace key
membrane
assembly.

Replace PCB
assembly.

Check the
connection
between
leadwire
connector and
PCB assembly.

2. Display shows a

number or figure
different from one
touched.

3. Random

programming
when touching
other pads.

4. Display is fixed

at some figure
and can not
accept any
input.

«
...
22
23
24
25
26
...
»

Содержание MC-807WR







































Отзывы:

Нет отзывов

Похожие инструкции для MC-807WR

Бренд: Wilfa Страницы: 69

Бренд: Brandt Страницы: 23

Бренд: Magic Chef Страницы: 24

Бренд: V-ZUG Страницы: 64

Maxi Oven 251-003

Бренд: Exido Страницы: 26

Бренд: DèLonghi Страницы: 52

Бренд: Daewoo Страницы: 15

Бренд: Maytag Страницы: 6

Da Vinci LLKDV13

Бренд: LLK Страницы: 29

Бренд: NEFF Страницы: 40

Бренд: Magic Chef Страницы: 19

Бренд: Blodgett Страницы: 17

Бренд: NEFF Страницы: 56

Advantium PSB9240BLTS

Бренд: GE Страницы: 76

Бренд: Electrolux Страницы: 7

Frigidaire FFMO1611L

Бренд: Electrolux Страницы: 20

Frigidaire FFCE1439L

Бренд: Electrolux Страницы: 20

Бренд: Electrolux Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды