manualshive.com logo in svg

LG MC-807WR, Руководство по обслуживанию

Поделиться
Скачать
LG MC-807WR Скачать руководство пользователя страница 15

5-5

H. FAN MOTOR ASSEMBLY REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, noise filter

and high voltage capacitor.

3) Remove the two screws holding the the suction guide

ASS’Y to the oven cavity and remove the high voltage
diode earth screw.

4) Remove the screw of the capacitor bracket.
5) Remove the two screws holding the fan motor ASS’Y

to the suction guide ASS’Y.

I. HIGH VOLTAGE CAPACITOR AND

DIODE REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, noise filter

and high voltage capacitor.

3) Remove the screw holding the suction guide ASS’Y to

the oven cavity and remove the high voltage diode
earth screw.

4) Remove the screw holding the high voltage 

capacitor bracket.

.

J. THE TURNTABLE MOTOR REMOVAL

1) Remove the turntable.
2) Remove the turntable shaft VERY CAREFULLY

with a slotted screwdriver.

3) Lay the unit down on its back.
4) Remove the turntable motor cover.

The turntable base cover is easily removed by

pinching the six parts with a wire cutting.

5) Disconnect the leadwire from the turntable motor

terminals.

6) Remove the screw securing the turntable motor to

the oven cavity ASS’Y

7) After repairing the motor, rotate the removed

turntable motor cover.

8) Fit the turntable motor cover’s projecting part to the

base plate slit.

NOTE:

1. Remove the wire lead from the turntable motor

VERY CAREFULLY.

2. Be sure to grasp the connector, not the wires, when

removing

H.V.
Capacitor

H.V.
Transformer

Suction
Guide

Wire Leads

Turntable Motor

Содержание MC-807WR







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды