LG MB-387W Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 37

background image

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

Approx.: 1.4 ohm
Approx.: 90 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

PRIMARY
TERMINAL

SECONDARY
TERMINAL

FILAMENT
WINDING
TERMINAL

COMPONENT TEST PROCEDURE

«
...
16
17
18
19
20
...
»

Содержание MB-387W






































Отзывы:

Нет отзывов

Похожие инструкции для MB-387W

In-A-Drawer MMDV30

Бренд: Dacor Страницы: 1

TSSTTV-ELXLDAF3

Бренд: Oster Страницы: 17

Classic SFPA6301TV

Бренд: Smeg Страницы: 52

Бренд: Atag Страницы: 76

Бренд: Saivod Страницы: 48

Бренд: Orbegozo Страницы: 32

Бренд: Maytag Страницы: 72

Бренд: Daewoo Страницы: 28

Бренд: Daewoo Страницы: 33

Бренд: Gaggenau Страницы: 52

B45M42 3 Series

Бренд: NEFF Страницы: 28

Бренд: Culina Страницы: 31

Бренд: John Lewis Страницы: 28

Бренд: Hanseatic Страницы: 66

Бренд: AEG Страницы: 28

Бренд: AEG Страницы: 152

Бренд: Domar Страницы: 40

Бренд: AEG Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды