LG MB-3832E страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 36

background image

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENT TEST PROCEDURE

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

Approx.: 1.4 ohm
Approx.: 90 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

PRIMARY
TERMINAL

SECONDARY
TERMINAL

FILAMENT
WINDING
TERMINAL

«
...
16
17
18
19
20
...
»

Содержание MB-3832E





































Отзывы:

Нет отзывов

Похожие инструкции для MB-3832E

Discovery EO127

Бренд: Dacor Страницы: 2

Бренд: Panasonic Страницы: 24

Бренд: FCI Home Appliances Страницы: 96

Бренд: Oster Страницы: 17

Бренд: Franke Страницы: 15

Бренд: DAEWOO ELECTRONICS Страницы: 33

Бренд: NEFF Страницы: 60

Бренд: Magic mill Страницы: 8

Бренд: Jenn-Air Страницы: 40

Бренд: Sammic Страницы: 20

Бренд: Jenn-Air Страницы: 104

7OFK 637J X RU/HA

Бренд: Hotpointt Ariston Страницы: 20

Бренд: Rangemaster Страницы: 32

Бренд: Jenn-Air Страницы: 16

Бренд: Daewoo Страницы: 36

EB 294-6 Operating and

Бренд: Gaggenau Страницы: 44

Бренд: Omega Страницы: 16

Бренд: Dacor Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды