LG MB-3832E Скачать руководство пользователя | Manualshive

Страница: 23 / 36

background image

5-13

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Fuse blows.

Continuity.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace primary
and monitor
switches.

No continuity.

Normal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Fuse blows again

Defective high volt-
age transformer.

Replace high volt-
age transformer.

Malfunction of the
monitor switch.

Replace primary
and monitor
switches.

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

Disconnect one
side of the wire
lead connected
from transformer
to the high
voltage
capacitor and
operate the unit.

Replace fuse

(TROUBLE 1) Oven lamp does not turn on when the timer knob is turned with door closed.

NOTE : All these switches must be replaced at the same time. Refer to page 5-6, 5-7

2. Fuse does not

blow.

No continuity.

No continuity.

Replace power
supply cord.

Defective oven
thermostat.

Defective power
supply cord.

Replace oven
thermostat.

Check continuity
of oven
thermostat.

Check continuity
of power supply
cord.

Continuity.

«
...
21
22
23
24
25
...
»

Содержание MB-3832E





































Отзывы:

Нет отзывов

Похожие инструкции для MB-3832E

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 30

Бренд: Samsung Страницы: 12

Бренд: Teka Страницы: 14

Бренд: Pelgrim Страницы: 54

Бренд: Rosewill Страницы: 8

Бренд: Palsonic Страницы: 19

Бренд: DAEWOO ELECTRONICS Страницы: 27

Бренд: Scarlett Страницы: 16

G3FERRARI G10029

Бренд: TREVIDEA Страницы: 48

Бренд: Zigmund & Shtain Страницы: 39

Бренд: MBM Страницы: 81

FMR 54 K.A (AN)

Бренд: Indes Страницы: 33

Бренд: Progress Страницы: 32

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 34

Бренд: Malloca Страницы: 42

Бренд: Falcon Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды