LG M2262D, Руководство по обслуживанию

Страница: 15 / 27

- 15 - Copyright ©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes LGE Internal Use Only
1-1) Confirmation
· We confirm whether “0xAA (RGB)” address of EEPROM
“0xA2” is “0xAA” or not.
· If “0xAA (RGB)” address of EEPROM “0xA2” isn’t “0xAA”, we
adjust once more
· We can confirm the ADC values from “0xA4~0XA9 (RGB)”
addresses in a page “0xA2”
*Manual ADC process using Service Remocon. After enter
Service Mode by pushing “ADJ” key, execute “4.ADC Adjust” by
pushing “ ” key at “ADC CALIBRATION: RGB”.
2) Component Gain/Offset Adjustment
· Convert to Component in Input-source
· Signal equipment displays
Impress Resolution 1080i
MODEL: 223 in Pattern Generator(1080i Mode)
PATTERN: 65 in Pattern Generator(MSPG-925 SERISE)*
Adjustment pattern (COMPONENT )
· Press the ADJ KEY and then select “2.ADC CALIBRATION
External” by using
/
(CH +/-) and press ENTER( ).
2-1) Confirmation
· We confirm whether “0xB3 (480i)/0xBC (1080i)” address of
EEPROM “0xA2” is “0xAA” or not.
· If “0xB3 (480i)/0xBC(1080i)” address of EEPROM “0xA2” isn’t
“0xAA”, we adjust once more
· We can confirm the ADC values from “0xAD~0XB2
(480i)/0XB6~BB (1080i)” addresses in a page “0xA2”
*Manual ADC process using Service Remocon. After enter
Service Mode by pushing “ADJ” key, execute “ADC Adjust” by
pushing " "key at “ADC CALIBRATION :COMPONENT”.
Impress Resolution 1080i
4.4 Function Check
1) Check display and sound
· Check Input and Signal items. (cf. work instructions)
1. TV
2. AV (SCART1/SCART2/CVBS)
3. COMPONENT (1080i)
4. RGB (PC : 1360 x 768 @ 60Hz –M1962D)
(PC : 1600 x 900 @ 60Hz –M2062D) (PC : 1920 x 1080 @
60hz –M2262D&M2362D/M2762D)
5. DVI (PC : 1360 x 768 @ 60Hz –M1962D)
(PC : 1600 x 900 @ 60Hz –M2062D) (PC : 1920 x 1080 @
60hz –M2262D&M2362D/M2762D)
6. HDMI
7. PC Audio In
* Display and Sound check is executed by Remote controller.
5. Total Assembly line process
5.1 Adjustment Preparation
· W/B Equipment condition
CA210: CH 9, Test signal: Inner pattern (85IRE)
· Above 5 minutes H/run in the inner pattern. (“power on” key of
adjust remote control)
· 15 Pin D-Sub Jack is connected to the AUTO W/B
EQUIPMENT.
· Adjust Process will start by execute I2C Command (Inner
pattern (0xF3, 0xFF).
* Caution
Color Temperature: COOL, Medium, Warm
One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0. (when R/G/B Gain are all C0, it
is the FULL Dynamic Range of Module)
EZ ADJUST
1. Tool Optionb :b 1261
2. ADC CALIBRATION External : Component
3. ADC CALIBRATION Internal
4. ADC ADJUST
5. W/B ADJUST
6. WHITE PATTERNb : OFF
7. EDID D.L
4. ADC ADJUST
MODEbbb : RGB
R-GAINbb : 115
G-GAINbb : 114
B-GAINbb : 114
R-OFFSETbb : 137
G-OFFSETbb : 131
B-OFFSETbb : 137
EZ ADJUST
1. Tool Optionb :b 1229
2. ADC CALIBRATION External : DTV
3. ADC CALIBRATION Internal
4. ADC ADJUST
5. W/B ADJUST
6. WHITE PATTERNb
: OFF
7. EDID D.L
Tool Optionbb :b 1229
Model Namebb :b M2794DP-PZ
Inchbbb :b 27
Toolbbb :b Mx94DP
DSUB Portbb :b RGB 0 (NEW)
Media Playerbb :b EMF-PM
HDMI Typebb :b 3-HDMI
OK to Download
bbbb
DOWNLOAD:
Cool 9,300k
o
K
X=0.285 ( ±0.003 )
Y=0.293 ( ±0.003 )
Medium 8,000k K
X=0.295 ( ±0.003 )
Y=0.305 ( ±0.003 )
Color
Temperature
Warm
6,500k
K
X=0.313 ( ±0.003 )
Y=0.329 ( ±0.003 )
M1962D
M2062D
M2262D
M2362D
M2762D
<Test Signal>
Inner pattern
(216gray,85IRE)
Cool Min : 120 Typ : 170
Medium
Min : 120 Typ : 170
Warm
Min : 120 Typ : 170
M1962D
Cool
Min : 170 Typ : 220
Medium Min : 170 Typ : 220
Luminance
(cd/m )
Warm Min : 170 Typ : 220
M2062D
M2262D
M2362D
M2762D
<Test Signal>
Inner pattern
(216gray,85IRE)
2
o
o