LG LW9424, Руководство пользователя

Страница: 29 / 46

Remote Configuration
29
This camera has two sensor ports and two alarm ports.
In the Event setup, actions which will be followed
Events can be configured. In Local setup, the actions
which will be followed Events at a local site can be
configured. In Remote setup, the actions which will be
followed Events at a Remote site can be configured.
The following table lists the possible actions for
events.
Action Description
Alarm out Triggers alarm (relay) port.
E-mail
Sends E-mail to the specified
address. AVI file can be attached
FTP
Upload AVI file to a specified FTP
server
Preset Move to the Preset position
Local Event Configuration
Sensor1 / Sensor2 / On Motion
Configure the actions when the sensor is activated.
Multiple actions can be set for a single event.
On Motion
Configure the actions when motion is detected.
Multiple actions can be set for a single event.
Alarm activation duration
Set the duration of alarm activation in case of an
event.
E-mail Notification
Specify the information to send event information,
when E-mail is selected as an event action. SSL does
not supported.
Server Address
: Enter an address of mail(SMTP) server.
SMTP can be IP address or Domain name(ex :
mail.lge.com)
Port: Specify a port for SMTP operation ( Port 25 is
the default port in SMTP operation . If a different
port is configured in the SMTP server, this port needs
to be changed accordingly).
Sender Address : Enter an account registered in the
SMTP server.
Authentication on SMTP server: Specify if the E-mail
server requires authentication for E-mail sending.
ID & password: When the server requires
authentication, ID and Password of an E-mail account
need to be entered.
SSL(Secure Sockets Layer ) : Selecting secured
connections with SSL.
Destination address : Enter Destination address. More
than one address can be entered by delimiting
comma (,) or semi-colon (;). Destination address can
take up to 60 characters.
Video Clip Attaching: Video clip stored at the
moment of event can be attached as an AVI or JPEG
file format. When dual encoding is enabled,
Primary
video , Secondary video (H.264 only) or JPEG Capture
can be selected. The duration of video clip can be
configured with
Pre-Event Time and Post-Event Time
in Event Record section.
Number of Frame: The number of JPEG frames is
configured. This setting is applicable only when JPEG
Capture is selected. The number of frames actually
captured may be less than this setting depending on
video setting or network condition.
E-mail Test :
E-mail sending can be tested with this
button. Event videos in avi or event images in JPEG
can be attached at E-mails. In Dual Encode
configuration, both of Primary Video and Secondary
Video can be configured. For Secondary Video, only
H.264 can be used. When JPEG Capture is selected,
plural images can be continuously captured and
attached at E-mails. In Number of Frame, the number
of the maximum frame can be configured. The actual
number of the frame may be less than the configured
number by network conditions and file sizes. Please
note that configured settings should be saved first by
pressing
Apply button before using E-mail Test
function.
One of the following messages will come as a result
of the test.
Message Description
E-mail sent
successfully Test E-mail has been sent successfully. Reception
in the client can be checked.
Failed to
connect SMTP
server Connection to the SMTP server failed. It is
necessary to check if the server is reachable and
server address and port are correct.
Authentication
failed The server is reachable but authentication failed.
ID and/or password need to be checked.
SMTP server
rejected the
mail
The server is reachable, but mail sending failed
due to a reason other than authentication. This
error happens often when the server
authenticates according to its own rule. For
example, IP addresses of a specific range or
addressed of a specific suffix are allowed.
An attached file can not exceed 2MB. If it is bigger
than 2MB, it will be divided by 2MB and