Connecting Display device
The video signal connection between the
camera and the monitor.
ALARM input connection
Connect sensor and alarm devices to
corresponding terminals accordingly.
E
D
C
B
A
G
F
H
Alarm device
Alarm device
Alarm device
Alarm device
RJ-45 Adapter cable
Port A
PORT A of the LW9422 series
Description
Color
ALARM IN COM
Black
ALARM IN 1
Brown
ALARM IN 2
Red
ALARM IN 3
Orange
ALARM IN 4
Green
ALARM output connections
E
D
C
B
A
G
F
H
Alarm device
RJ-45 Adapter cable
Port B
GND
IP Reset
Alarm device
PORT B of the LW9422 series
Description
Color
ALARM OUT 1A
Blue
ALARM OUT 1B
Violet
ALARM OUT 2A
Gray
ALARM OUT 2B
White
IP RESET
Pink
GND
Red/White
CAUTION:
Output specifications are lowactive, open-
collector and a drive capacity of DC 30 V 1 A
/ AC 125 V 0.3 A. Connecting the alarm out
incorrectly may cause damaging the camera.
Connecting Network
Connect the IP camera to your network
using a standard RJ-45 network cable as
shown below.
Router
Connecting power source
Connect a AC 24 V or PoE+ power source to
the power input terminal as shown below.
(Connect to the AC 24 V UL Listed, Class 2
Power Supply only on the unit.)
NOTE:
In case of connecting both AC 24 V and
PoE+, PoE+ has a priority.
AC 24 V
or
PoE+
Connecting Microphone and
Speaker Device
Optionally connect an active speaker and/or
external microphone with a built-in amplifier.
NOTE:
Keep the microphone away from the speaker
to avoid howling.
You can record your surveillance environment with the SD card even if the network is disconnected
condition.
To insert the SD card
1. Remove the dome cover.
2. Insert the SD card carefully as shown in the following illustrations. Make sure the SD card
terminal position before insert the SD card. Push the back end of the SD card to fix it at the last
step.
NOTES:
•
Do not use the power too much when you insert the SD card. The SD card may be
damaged.
•
If you insert the SD card in the wrong position, the SD card may be damaged or it may
cause the malfunction of the SD Card Slot.
•
Keep the terminal part of the SD card in clean. Be careful the terminal part of the SD card
not to dusty.
•
As the SD card is consumable, the SD card end its days and may be not able to save data if
you use it more than over certain times. In this case, replace SD card to buy a new one.
Remove the SD card
1. Press the back end of the SD card to release the lock condition.
2. Take the SD card out carefully from the camera. It may cause a malfunction of the SD card
or the SD card slot if you use the power too much at lock status.
CAUTION:
•
If you install the SD card on the camera and remove with the SD card condition indicator
lights on, you must unmount the SD card by using the [SD Card > Configuration > Disk
Management > Unmount] menu. The SD card data is compromised or the camera may
not operate normally, if you remove the card without use [Unmount] function.
•
Do not insert Micro SD card to SD card adapter. It is recommended to use a standard SD
card.
•
Insert the SD card before install the camera.
•
LG Electronics is not responsible for deleted data caused by user mishandling when you
insert or remove the SD card.
Wall mount (optional)
Install the camera by the following order.
1. Install the wall mount assembly as
shown below.
2. Drill a hole on the wall where you want
to install the pipe. Pass the connection
cable through the wall mount assembly
so that they hang down.
3. Connect the safety cable to the camera
in order to prevent a camera from falling.
4. Connect the cable to the camera jack.
5. Assemble the camera to the mounting
adaptor by turning it clockwise. Tighten
the M3 SAMS Screws and then align the
cover adaptor and main body.
CAUTION:
Remove the dome cover carefully to prevent
falling.
Pendant mount (optional)
Install the camera by the following order.
1. Install the pendant mount assembly.
2. Drill a hole on the wall where you want
to install the pipe. Pass the connection
cable through the pendant mount
assembly so that they hang down.
3. Connect the safety cable to the camera.
4. Connect the cables to the camera jack.
5. Assemble the camera to the mounting
adaptor by turning it clockwise. Tighten
the M3 SAMS Screws and then align the
cover adaptor and main body.
Parapet mount (optional)
1. Install the parapet mount assembly as
shown below.
2. Drill a hole on the wall where you
want to install the parapet. Pass the
connection cable through the parapet
mount assembly so that they hang
down.
3. Connect the safety cable to the camera.
4. Connect the cables to the camera jack.
5. Assemble the camera to the mounting
adaptor by turning it clockwise. Tighten
the M3 SAMS Screws and then align the
cover adaptor and main body.
Connection
Using the SD Card
Installation
