manualshive.com logo in svg

LG LMV1640DB, Руководство по обслуживанию

Поделиться
Скачать
LG LMV1640DB Скачать руководство пользователя страница 6

PRECAUTIONS ON INSTALLATION

A. Plug the power supply cord into a 120V AC, 60Hz,

single-phase power source with a capacity of 15A
or 20A.

B. Avoid placing the unit in a location where there is

direct heat or splashing water.

C. Install the unit on the mounting plate firmly.
D. Place the unit as far away as possible from TV,

radio, etc. to prevent interference.

GROUNDING INSTRUCTIONS

For personal safety, this appliance must be fully
grounded at all times.

In the event of an electrical short circuit, grounding
reduces the risk of electrical shock.
The plug must be plugged into an outlet that is
properly installed and grounded.

3-1

INSTALLATIONS

BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.

CAUTION

This unit is equipped with a 3-prong plug for your
safety. If the wall outlet is a grounded 3-hole type,
the unit will be grounded automatically.

WARNING

Improper use of the grounding plug can result in a
risk of electric shock.
Do not, under any circumstances, cut or remove the
third ground prong from the power cord plug.

Properly Polarized
and Grounded
Outlet

Plug with Ground
Prong

Содержание LMV1640DB














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды