background image

2

Part 1

SAFETY

1

BEFORE YOU BEGIN

Remove all tape and packing materials before using the range. 
Dispose of all plastic bags after unpacking the range. Never allow children to play with packing materials.

IMPORTANT SAFETY INSTRUCTIONS

Read and follow all instructions before using your oven to prevent the risk of fire, electric shock, personal injury, or
damage when using the range. This guide does not cover all possible conditions that may occur. For further
assistance contact your service agent or manufacturer.

This is the safety alert symbol. This symbol alerts you to potential hazards that can cause personal injury to
you and others. All safety messages will follow the safety alert symbol with either the word  “WARNING” or
“CAUTION”.

This symbol will alert you to hazards or unsafe practices which could cause serious
bodily harm or death.

WARNING

This symbol will alert you to hazards or unsafe practices which could cause bodily
injury or property damage.

CAUTION

WARNING

• The information in this manual should be followed exactly.

- A fire or electrical shock may result causing property damage, perasonal injury or death.

• DO NOT step or sit on oven door. Install the Anti-Tip Bracket supplied with the range.

- The range could be tipped and injury might result from spilled hot liquid, food, or the range itself.
- If the range is pulled away from  the wall for cleaning, service, or any other reason, ensure that the Anti-Tip Device is properly

reengaged when the range is pushed back against the wall.

• New branch-circuit installations (1996 NEC) for mobile homes, recreational vehicles, and

installations where local codes do not allow grounding through the neutral wire require a 4-
conductor UL listed range cord or 4 wire conduit connection.

• The middle (neutral or ground) wire of a 3 wire power cord or a 3 wire conduit has to be connected

to the middle post of the main terminal block. The remaining two wires of the power cord or
conduit have to be connected to the outside posts of the main terminal connection block.

- Failure to do so can result in electrical shock, severe personal injury or death.

• Only a 4-conductor power-supply cord kit rated 120/240 volts, 50 amperes and marked for use with

ranges with closed-loop connectors or open-end spade lugs with upturned ends shall be used.
The middle (neutral) wire of the power cord or 4-wire conduit has to be connected to the middle
post of the main terminal block. The other two wires of the power cord or conduit have to be
connected to the outside posts of the main terminal connection block. The 4th ground wire must
be connected to the frame of the range with the ground screw. 

- Failure to do so can result in electrical shock, severe personal injury or death.

CAUTION

• Make sure that the wall covering, countertop and cabinets around the range can withstand

the heat (up to 194°F) generated by the range.

- Discoloration, delamination or melting may occur.
- This range has been designed to comply with the maximum allowable wood cabinet temperatures of 194°F.

• Cabinet storage space located above the surface units should be avoided.
• Install a range hood that projects horizontally a minimum of 5 inches beyond the bottom of

the cabinets If cabinet storage is to be provided.

- The risk of burns or fire by reaching over the heated surface elements can be reduced.

Содержание LFRF0222S











Отзывы: