LG LFC21776ST Скачать руководство пользователя страница 5

Страница: 5 / 62

3. DISASSEMBLY

- 5 -

3-1 DOOR

Refrigerator door

1. Remove the top hinge cover and disconnect the wire

harness.

2. Remove the ground screw.
3. Rotate the lever hinge and lift off hinge.
4. Lift off the refrigerator door.
5. Replace in the reverse order.

Door gasket replacement

1. Insert gasket bracket clips

1) Insert gasket bracket edge beneath door frame edge.
2) Turn upper gasket bracket spring so that both spring

ends are in the door channel.

3) Push in clip until you hear it snap securely into place.

4) Push in remaining two clips until you hear each snap

securely into place.

Note : Make sure that no part of gasket bracket edge

protrudes from beneath door frame edge.

2. Remove gasket bracket clips

There are two clips on each door. Start bracket removal
near one of the middle clips.
1)Pull gasket back to expose gasket bracket clip and

door frame.

2)Insert a flat tip screwdriver into seam between gasket

bracket and door frame and pry back until clips snaps
out.

3)Continue prying back along seam until all clips snap

out.

3. Remove gasket

Pull gasket free from gasket channel on the three
remaining sides of door.

Figure 2

Frame Cover

Handle

Figure 5

Correct

Incorrect

Figure 3

Gasket

Bracket Clip

Gasket

Bracket

Flat Tip

Screwdriver

Figure 4

Spring

Gasket
Bracket Clip

Figure 1

HINGE COVER

HINGE

Door gasket removal

1. Remove door frame cover

Starting at top of cover and working down, snap cover
out and away from door.

Door

Frame

Door

Frame

Содержание LFC21776ST































































Результаты поиска

Содержание LFC21776ST

Отзывы:

Бренды по названию

Популярные бренды

LG LFC21776ST, Руководство по обслуживанию

Результаты поиска

Содержание LFC21776ST

Отзывы:

Бренды по названию

Популярные бренды