background image

28

Problem

Possible Causes

Solutions

THERE´S WATER IN 

THE DRAINING BIN

• The refrigerator is in defrosting 

cycle.

• It’s more humid than usual.

• The water will evaporate. It is normal that some 

water falls on the bin.

• It might take a while for the water to evaporate. 

This is normal when the weather is hot and humid.

THE 

REFRIGERATOR 

SEEMS TO MAKE 

TOO MUCH NOISE

• The sounds may be normal for your 

refrigerator. 

• Refer to the 

Understanding Sounds You May Hear

 

section.

THE ICE MAKER IS 

NOT PRODUCING 

ICE OR ICE CUBES 

ARE FREEZING 

TOO SLOWLY

• The smallest size of ice cubes is 

selected. 

• Door left open. 

• Wait 24 hours after hook-up for ice production. 

See the 

Adjusting the Controls

 section.

• Check to see if something is holding the door 

open.

THE ICE CUBES 

ARE TOO SMALL

• Smaller cube size level is selected.

• The water supply valve is blocked. 

• Select a bigger size for the ice cubes.

• Call a plumber to clean the valve.

THE DOORS ARE 

HARD TO OPEN

• The gaskets are dirty or sticky. 

• The door opens itself as soon as 

you close it. 

• Clean the gaskets and surface that they are in 

contact with. Use a damp cloth with paraffin also 

apply over the seal rings.

• When you open the door, the warm air enters 

in the refrigerator. When this air is cooled down 

it occupies less volume and creates a vacuum 

effect. If it is difficult to open wait 5 minutes then 

check.

THE ICE MAKER 

DOES NOT WORK

• The ice maker is off. 

• The water supply is down or not 

plugged. 

• The freezer temperature is warm. 

• The ice cubes turn off the ice maker.

• Turn the ice maker to the position on (I).

• Read the section 

Connecting the Water Line.

• Wait 24 hrs for the freezer to reach its ideal 

temperature.

• Hand level the ice cubes.

THE TEMPERATURE 

IS TOO HOT 

OR THERE´S 

HUMIDITY FORMED 

INSIDE THE 

REFRIGERATOR

• The air vents are blocked. The 

cool air flows from freezer to the 

refrigerator and returns thru the 

vents that dive this section. 

• The doors open very easily. 

• The refrigerator control has not been 

adjusted for the room conditions.

• A large amount of food is just been 

placed inside the refrigerator.  

• The food has not been well packed 

in each bin. 

• The doors haven’t been closed 

correctly. 

• The weather is humid. 

• The auto-defrosting cycle is over. 

• With your hand find the vents and move and 

package that might be blocking the air flow. See 

the 

Multi Flow

 Section.

• When the doors are opened the warm and humid 

air enters. To keep your refrigerator cool, take what 

you need once and you’re your food organized to 

make it easy to find. Close the door a soon as 

you can.

• Wait 24 hours to stabilize the temperature. If the 

temperature is cold or hot, move the control until 

the desire temperature is reached.

• After adding food to the refrigerator this will warm 

up. It might take some hours for the refrigerator to 

reach its temperature.

• Wrap the food evenly and before packing anything 

dry all the bins to avoid humidity. If it is necessary, 

pack the food according to the section 

Food 

Storage Guide

.

• Read 

Doors will not Close Correctly

 section.

• In humid weathers, the air contains humidity, 

which introduces it self if the doors are opened.

• It’s normal that some water props get formed 

after the defrosting cycle is completed.

TROUBLESHOOTING GUIDE

MFL67241802_frontier.indd   28

6/10/2011   9:41:09 AM

Содержание LFC20786 Series































Отзывы: