LG LBC22520TT Скачать руководство пользователя страница 20

Страница: 20 / 49

6-5 REFRIGERATION CYCLE

• Troubleshooting Chart

CAUSE

TEMPERATURE

OF THE

COMPRESSOR

REMARKS

STATE OF

THE UNIT

STATE OF THE

EVAPORATOR

PARTIAL
LEAKAGE

Freezer
compartment and
refrigerator don’t
cool normally

COMPLETE
LEAKAGE

PARTIAL
CLOG

WHOLE
CLOG

MOISTURE
CLOG

COMPRE-
SSION

NO
COMPRE-
SSION

Freezer
compartment and
refrigerator don’t
cool normally

Freezer
compartment and
refrigerator don’t
cool.

Cooling operation
stops periodically.

Freezer and
refrigerator don’t
cool.

No compressing
operation.

Low flowing sound of
refrigerant is heard and frost
forms in inlet only.

Flowing sound of refrigerant
is not heard and frost isn’t
formed.

Flowing sound of refrigerant
is heard and frost forms in
inlet only.

Flowing sound of refrigerant is
not heard and frost isn’t
formed.

Flowing sound of refrigerant is
not heard and frost melts.

Low flowing sound of
refrigerant is heard and frost
forms in inlet only.

Flowing sound of refrigerant is
not heard and there is no
frost.

A little higher than
ambient
temperature.

- Refrigerant level is low due to a
leak.
- Normal cooling is possible by
restoring the normal amount of
refrigerant and repairing the leak.

Equal to ambient
temperature.

- No discharging of refrigerant.
- Normal cooling is possible by
restoring the normal amount of
refrigerant and repairing the leak.

A little higher than
ambient
temperature.

- Normal discharging of the
refrigerant.
- The capillary tube is faulty.

Equal to ambient
temperature.

- Normal discharging of the
refrigerant.

Lower than ambient
temperature.

- Cooling operation restarts when
heating the inlet of the capillary
tube.

A little higher than
ambient
temperature.

- Low pressure at high side of
compressor due to low
refrigerant level.

Equal to ambient
temperature

- No pressure in the high pressure
part of the compressor.

- 20 -

Leakage Detection

YES

Check if compressor
runs.

Check if frost
forms in
Evaporator.

Observe the discharged
amount of Refrigerant.

Inject refrigerant in compressor
and check cooling operation.

Clogged by dust.

Gas leakage.

Faulty
Compressor.

Moisture Clog

Check if oil
leaks.

Frost formed normally

Normal amount

None or too much

(Find the leak and repair it)

Frost formed normally

No frost
or frost forms
in inlet only

Check Compressor

Observe the discharging point of the refrigerant, which may be in the oil discharging part of the compressor and in a hole
in the evaporator.

Содержание LBC22520TT


















































Результаты поиска

Содержание LBC22520TT

Отзывы:

Бренды по названию

Популярные бренды

LG LBC22520TT, Руководство по обслуживанию

Результаты поиска

Содержание LBC22520TT

Отзывы:

Бренды по названию

Популярные бренды