background image

Introduction

The identification plate, with technical data, serial number and 

marking is clearly visible under the casing.

The plate on the casing must not be removed.

Before connecting the device, make sure that it has been regulated for 

the type of gas that will feed it, checking the label under the casing.

Do not put

 pans without perfectly smooth and flat bottoms on the 

cooking hob grids.

Do not use 

recipients or griddle plates that extend beyond the 

external perimeter of the hob.

The hob is to be used by adults only.

 Do not let unsupervised 

children play with the hob.

This appliance is designed for cooking food and it shall not be used 

as a space heater. 

Do not spray aerosols in the vicinity of this appliance while it is in operation.

The manufacturer declines all responsibility 

for damage to persons or things 

caused by non-observance of the above prescriptions or by interference with 

any part of the appliance or by the use of non-original spares.

THIS APPLIANCE IS MARKED ACCORDING TO EUROPEAN DIRECTIVE 2002/96/

EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). THIS 

GUIDELINE IS THE FRAME OF EUROPEAN-WIDE VALIDITY OF RETURN AND 

RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT.

DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE 

APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.

DO NOT MODIFY THIS APPLIANCE

4

 

 

Содержание HB6422BGF





















Отзывы: