- 1 -
Copyright © 2010 LG Electronics. Inc. All right reserved.
Only for training and service purposes
LGE Internal Use Only
3. TECHNICAL BRIEF
͑
ͽͶ͑ͺΟΥΖΣΟΒΝ͑ΆΤΖ͑ΟΝΪ͑
͑
3.6.3 ASM + GSM PAM (U100, SKY77544)
SKY77544 is a transmit and receive Front End Module (FEM) designed in a very low profile (0.9 mm), compact form
factor for quad-band cellular handsets comprising GSM850/900, DCS1800, and PCS1900 operation — a complete
transmit VCO-to-Antenna and Antenna-toreceive SAW filter solution. The FEM also supports Class 12 General Packet
Radio Service (GPRS) multi-slot operation and EDGE Polar Modulation. WCDMA switch-through support is provided
by three dedicated high-linearity ports.
The module consists of a GSM850/900 PA and DCS1800/PCS1900 PA block, impedancematching circuitry for 50 Ω
input and output impedances, Tx harmonic filtering, high linearitylow insertion loss switches, and a CMOS Power
Amplifier Control (PAC) block. A custom silicon integrated circuit contains decoder circuitry to control the RF switch
while providing a low current external control interface. An integrated temperature sensor provides an analog
voltage based on the temperature of the module.
Fabricated in InGaP/GaAs, the Heterojunction Bipolar Transistor (HBT) PA blocks support the GSM850/900 bands
and DCS1800/PCS1900 bands. Both PA blocks share common power
supply pads to distribute current. The output of the PA block and the outputs to the seven
receive pads connect to the antenna pad through a highly linear antenna switch. The WCDMA
and Rx ports feature a 0 volts DC offset level, which eliminates any need for external blocking capacitors. The
InGaP/GaAs die, switch die, Silicon (Si) controller die, and passive components are mounted on a multi-layer
laminate substrate and the entire assembly is encapsulated with plastic overmold.
RF input and output ports of the SKY77544 are internally matched to a 50 Ω load to reduce the number of external
components for a quad-band design. Extremely low leakage current of the FEM maximizes handset standby time.
Band selection and control of transmit and receive RF signal flows are performed by use of four external control
pads. See
Figure 1.9
shown on overleaf. Mode of operation Tx, Rx, Band (GSM850, GSM900, DCS, PCS, and UMTS) is
controlled with 4 logic inputs: BS1, BS2, Mode, and TxEN. Proper timing of the TxEN input and the VAPC input
ensures high isolation between the antenna and Tx-VCO while the VCO is being tuned prior to the transmit burst.
The Enable input controls the initial turn-on of the PAC circuitry to minimize battery drain.
The integrated power amplifier control (PAC) function provides envelope amplitude control by reducing sensitivity
to input drive, temperature, power supply, and process variation.
Содержание GT540
