LG GR-B197DVCA Скачать руководство пользователя страница 106

Страница: 106 / 119

2. HANDLE

1) Put blade screwdriver into a groove on the side of a

Deco handle and lift up a little bit in arrow

direction

and push up with hand in arrow

direction and

disconnect.

2) Put blade screwdriver into a groove on the side of a

DECO handle and lift up in arrow direction

and push

down with hand in arrow direction

and disconnect.

3) Push up a piece handle

in arrow direction with hand

and disconnect.

4) Turn screw in arrow direction with a cross driver and

disconnect.

3. SHROUD, GRILLE FAN

1) Loosen two screws after disconnecting a cap screw of a

grille fan(U) with a balde screwdriver.

2) Disassembly of a grille fan(U) : Pull forward after

opening hook at

➝

part with a blade screwdriver.

3) Disconnect housing A of a grille fan (L) from the main

body.

4) Disassembly of a grille fan (L) : Hold upper part of a

grille fan(L) and pull forward carefully.

5) Loosen two screws.

6) Disassembly of shroud. F(U) : Disconnect housing of B

after removing two rail guides with a blade screwdriver.

7) Disassembly of shroud. F(U) : Hold upper part and pull

forward.

8) Check foam PU sticking conditions around a shroud,

F(U) and F(L) during assembling. If damaged, torn or
badly sticked, assemble with a new one after sealing
well.

4. ICEMAKER ASSY

1. Dispenser Model

1) How to disassemble:

(1) Remove ice bank from the freezer compartment.

(2) Loosen two screws on the upper part of icemaker

bracket.

(3) Disconnect icemaker bracket so that it can slide

forward.

(4) Disconnect icemaker housing and sensor housing.

(5) Disconnect icemaker horizontally by pressing bracket

hook part. ( Don’t disassemble further. The set value
may be changed.)

2) How to assemble : The assembly is the reverse order of

the above disassembly.

Note :

When the ice tray is not horizontal after assembly,
assembly must be wrong. Check and assemble
again.

HOW TO DISASSEMBLE AND ASSEMBLE

- 106 -

Handle, Deco

Handle, Piece

Screw

Bracket, Ice Maker

Hook

Ice Maker Unit

Lever

Tray, Ice

Sensor

Insulation

Cover, Sensor

Содержание GR-B197DVCA
























































































































Результаты поиска

Содержание GR-B197DVCA

Отзывы:

Похожие инструкции для GR-B197DVCA

Бренды по названию

Популярные бренды

LG GR-B197DVCA, Руководство по обслуживанию

Результаты поиска

Содержание GR-B197DVCA

Отзывы:

Похожие инструкции для GR-B197DVCA

Бренды по названию

Популярные бренды