background image

7-1-5 BUZZER SOUND

1. When the button on the front Display is pushed, “Ding-” sound is produced and it works as follows.

7-1-6 DEFROSTING

1. The defrosting is performed each time when the total running time of the compressor reaches 7 hours.

2. After the power is turned on (or restored after a power failure), the defrosting starts when the total running time of the

compressor reaches 4 hours.

3. When the temperature of the defrosting sensor reaches 13 °C or above, the defrosting stops.  If the temperature does not

reach 13 °C in 2 hours after the defrosting starts, the defrosting error code is displayed. 
(Refer to 7-1-10. Error Diagnostic Mode.)

4. With the defective defrosting sensor (cut or short-circuited wire), the defrosting will not be performed.

7-1-7 SEQUENTIAL OPERATION OF ELECTRIC COMPONENTS

The electric components, such as the comp, defrosting heater, and cooling fan, start sequentially to avoid the noise and
damage to the part, which may result from the simultaneous start of various components on turning the power on or after
the completion of a test.

Condition of Operation

Operating Sequence

If the temp of the defrosting 
sensor is 45 °C or above
(For the initial use after the 
purchase or grounding)

If the temp of the defrosting 
sensor is below 45 °C
(After a power failure or SVC)

When returned from the Test mode

- 20 -

POWER

in 0.5 sec

COMP

in 0.5 sec

COOLING FAN

ON

ON

ON

ALL LOADS

in 7 min

COMP

in 0.5 sec

COOLING FAN

OFF

ON

ON

POWER

in 0.5 sec

DEFROSTING

in 5 sec

DEFROSTING

ON

HEATER ON

HEATER OFF

in 0.5 sec

COMP

in 0.5 sec

COOLING FAN

ON

ON

When the power is turned on

Содержание GN-B492Y*C


















































Отзывы: