LG GB107 Скачать руководство пользователя страница 103

Страница: 103 / 115

103

1.3

Test Procedure

1.3.1

Auto test sequence

Operator not need to insert test SIM card, and enter ”

*8*

” to check “auto test” as below.

When operator into function test mode, we just press “yes” key or “enter” key to into next test item.

When use auto test, every test item always turn on together.

No. Test item

Verifying item

1 LCD

Display check (

All white, all black, red, blue, green test

)

Every screen is 0.5 second

Speaker and Melody function check
(Always on/Set max volume)

All Keypad LED

2 LED/IllumiV Melody

Vibrator function check (Always on)

All keys function check
Method 1: screen shows all icons for key and operator press
key one by one then it disappear in screen.
Method 2: screen shows icon of key one by one then operator
press it as phone instruction.

3 Ke Receiver

Receiver check

4 Audio

Main Mic to Main Receiver audio loop check

5 Headsets (Earpiece)

Aux-Mic to Aux Receiver audio loop check

6 FM

Default handset in FM channel 100.7 MHz
1. Testing FM through headset (earpiece)
2. Testing FM through SPK

7 Antenna

Antenna circuit check by Radiation Power

(Turn on GSM Power level 5 @ Ch40 for 900/1800 band
Turn on GSM Power level 5 @ Ch190 for 850/1900 band)

Содержание GB107




















































































































Результаты поиска

Содержание GB107

Отзывы:

Похожие инструкции для GB107

Бренды по названию

Популярные бренды

LG GB107, Руководство по обслуживанию

Результаты поиска

Содержание GB107

Отзывы:

Похожие инструкции для GB107

Бренды по названию

Популярные бренды