LG DLEX8000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 58

LG DLEX8000 Скачать руководство пользователя страница 35

35

37

NOTE:

This test has two parts. The best test of the moisture sensing system is done in the diagnostic mode. This

FUNCTIONAL TEST will test the sensor bars, wiring harness and PCB operation. If the results of this test are normal,

the sensor system and PCB response are normal. The problem is somewhere else.

FUNCTIONAL TEST (Control)
1. Enter the diagnostic mode. (See DIAGNOSTIC TEST MODE.)
2. With the door closed, press the START/PAUSE button once. The dryer will start tumbling without heat.
3. Open the door. The drum will stop tumbling and the “dE” error code will be displayed and the chime will sound several times (if turned on).
4. With one hand, reach into the drum and place your fingers across the moisture sensor bars.

(CAUTION: The dryer drum will turn in this test. Your hand will be close to the rotating drum vanes. Keep your hand close to the filter housing to
avoid being hit by the moving vanes.)

5. Use your other hand to press the door switch. The dryer drum will start rotating automatically.
6. Observe the numerical display. Depending on conditions, the number displayed should be between 30 and 255. The numbers should start

decreasing as the control senses the moisture in your skin.

7. After you have observed the number decreasing, remove your fingers from the sensor bars. The numbers will continue to decrease for a few

seconds (minimum 30) and the begin to increase (maximum 255).

8. If this test fails, proceed with the MECHANICAL TEST below.

Test 4

Moisture sensor

YES

YES

YES

YES

NO

NO

Disconnect the NA8 connector from

the main PCB. Measure the resistance

between the NA8-

⑧

Take NA8 Connector from

the controller.

Metal wire (Short)

chassis ground screw.

Is the resistance <1 ?

Put a jumper between NA8-

⑥

(YL)

and NA8-

⑦

(BL) to create a circuit

connection for the continuity test in

the next step.

Measure the resistance between

the two moisture

sensor bars on the in the lint filter

housing inside

the drum. Is the resistance <1 ?

Check all connections and wires

between the NA8

terminal at the main PCB and the

sensor bars.

Check the resistance is 0

•

Measure the resistance of all wires.

Resistance should be <1 ?

•

Check all sensor harness connectorsfor corrosion,

loose/bent pins, broken wires, etc.

•

Check all harness wires between the main PCB and the

sensor for cuts, or broken wires.

•

Check all wiring

harness connections

wire and Ground

screws.

•

Replace the main

PCB.

(GN) pin and a

«
...
33
34
35
36
37
...
»

Содержание DLEX8000



























































Отзывы:

Нет отзывов