background image

How to Install

Hanging and fixing

Mount the hood body on the body fixing bracket which was installed.(Fig.2) Then align the
center of body with the vertical line which was drawn. Adjust screws(a) to level the hood body.
Secure the ‘Bracket of the body’ to the wall by fastening 2 screws using washers into the wall
plugs which was inserted.(b)(M4XL30)

Connection

Place the damper on the exhaust hole of the hood body.
Apply the adhesive tape between damper and top surface
not to be taken off during operation.
Connect the pipe between damper hole of the hood body
and one of the kitchen wall.
The rigid or flexible pipe may be used, and the 120mm or
150mm pipe may be used.
But, the choice is left to the installer.
If the diameter of the pipe is 120mm, diameter reducer
should be placed on the damper. (When using 150mm pipe, 
the reducer is not necessary.)
Connect the pipe with exhaust hole using the clamps. 
(The pipe and clamps are not provided.)
Connect the power plug to the main supply.

Chimney flue fixing

Secure the upper chimney to the chimney bracket using the 2
screws provided. (M4 X L12)
A little widen the sides of the lower chimney and put the side
flange between the upper chimney and wall. 
Then pull the lower chimney down until contacting with body.
Secure the lower chimney to the body bracket using the 2
screws provided. (M4 X L12)

7

(a)

(b)

Body fixing bracket

Bracket of 
the body

(a)

(b)

Fig.2

Fig.3

Fig.4

GB

Содержание DC9201SAU













Отзывы: