LG AS-H1863*M3 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 75

background image

Service Manual 23

Installation

1. Remove the control cover from the unit by loos-

ening the screw.
Connect the wires to the terminals on the control
board individually.

2. Secure the cable onto the control board with the

cord clamp.

3. Refix the control cover to the original position

with the screw.

4. Use a recognized circuit breaker "A"

between the power source and the unit.
A disconnecting device to adequately disconnect
all supply lines must be fitted.

Terminal block

Over 5mm

Cover control

Connecting cable

Connecting cable

CAUTION: After the confirmation of the above conditions, prepare the wiring as
follows:

1) Never fail to have an individual power circuit specifically for the air conditioner. As for the method of wiring,

be guided by the circuit diagram posted on the inside of control cover.

2) The screw which fasten the wiring in the casing of electrical fittings are liable to come loose from vibrations

to which the unit is subjected during the course of transportation. Check them and make sure that they are
all tightly fastened. (If they are loose, it could cause burn-out of the wires.)

3) Specification of power source.
4) Confirm that electrical capacity is sufficient.
5) See to that the starting voltage is maintained at more than 90 percent of the rated voltage marked on the

name plate.

6) Confirm that the cable thickness is as specified in the power source specification.

(Particularly note the relation between cable length and thickness. (Refer to page 24))

7) Always install an earth leakage circuit breaker in a wet or moist area.
8) The following would be caused by voltage drop.

•

Vibration of a magnetic switch, which will damage the contact point, fuse breaking, disturbance of the normal func-

tion of the overload.

9) The means for disconnection from a power supply shall be incorporated in the fixed wiring and have an air

gap contact separation of at least 3mm in each active(phase) conductors.

Outdoor Unit

7ks~18k

~26k

~30k

~38k

15

20

30

40

Circuit

Breaker

(A)

Grade

Connecting the Cables to the Outdoor Unit

«
...
17
18
19
20
21
...
»

Содержание AS-H1863*M3












































































Отзывы:

Нет отзывов

Похожие инструкции для AS-H1863*M3

IAQ 1" Polarized Media Air Cleaner

Бренд: EnviroAire Страницы: 4

Бренд: U-Earth Biotech Страницы: 16

GWH09MA-A3DNC5A

Бренд: Gree Страницы: 25

Бренд: HANDY COOLER Страницы: 2

Бренд: Unitary products group Страницы: 16

Бренд: BASETech Страницы: 12

Бренд: Technibel Страницы: 8

Бренд: AllerAir Страницы: 1

GSC 18 FV 5 HRML

Бренд: Godrej Страницы: 24

Бренд: Airwell Страницы: 20

Бренд: Electra Страницы: 151

Бренд: Hyundai Страницы: 40

XP14-018-230-01

Бренд: Lennox Страницы: 50

Бренд: Air Oasis Страницы: 2

Duplex Water-Cooled Hermetic CenTraVac

Бренд: Trane Страницы: 80

U-MATCH B Series

Бренд: Gree Страницы: 133

Бренд: Samsung Страницы: 21

Бренд: Samsung Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды