LG ARNU48GBRZ2 Скачать руководство пользователя страница 11

Страница: 11 / 31

Installation Manual

Installation

ENGLISH

• Select and mark the position for fixing bolts.
• Drill the hole for set anchor on the face of ceiling.

• Insert the set anchor and washer onto the suspen-

sion bolts for locking the suspension bolts on the
ceiling.

• Mount the suspension bolts to the set anchor firmly.
• Secure the installation plates onto the suspension

bolts (adjust level roughly) using nuts, washers
and spring washers.

1 Set anchor

Old building

New building

2 Plate washer

3 Spring washer

4 Nut

5 Suspension
bolts

Connect the wires to the terminals on the control board individually according to the outdoor unit connection.
• Ensure that the color of the wires of outdoor unit and the terminal No. are the same as those of indoor unit respectively.

Clamping of cables

1) Arrange 2 power cables on the control panel.

2) First, fasten the steel clamp with a screw to the inner boss of control panel.

3) For the cooling model, fix the other side of the clamp with a screw strongly. For the heat pump model, put the

0.75mm

cable(thinner cable) on the clamp and tighten it with a plastic clamp to the other boss of the control panel.

BR Chassis (48k)

Terminal Block Indoor

1(L)

2(N)

3(A)

4(B)

INDOOR POWER

IDU

Outdoor unit Indoor unit

Central controller

SODU SODU

DRY1 DRY2 GND

INTERNET

12V

Outdoor unit

INPUT

B8 Chassis (76/96k)

Terminal Block Indoor

1(L)

2(N)

3(A)

4(B)

Terminal Block

Indoor Power Input

IDU

Outdoor unit Indoor unit

Central controller

SODU SODU

DRY1 DRY2 GND

INTERNET

12V

Outdoor
unit

Wiring Connection

Indoor Unit Installation

CAUTION : Tighten the nut and bolt

to prevent unit falling.

WARNING : Make sure that the screws of the terminal are free from looseness.

CAUTION

The Power cord connected to the unit should be selected according to the following specifications .

Содержание ARNU48GBRZ2
































Результаты поиска

Содержание ARNU48GBRZ2

Отзывы:

Похожие инструкции для ARNU48GBRZ2

Бренды по названию

Популярные бренды

LG ARNU48GBRZ2, Руководство по установке

Результаты поиска

Содержание ARNU48GBRZ2

Отзывы:

Похожие инструкции для ARNU48GBRZ2

Бренды по названию

Популярные бренды