LG A3UQ24GFD0 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 39

background image

22

FLARING WORK AND CONNECTION OF PIPING

ENGLISH

(

(1) Ceiling-suspended type

(2) Wall-mountde type

Procedure

1

Fix the furnished hanger metal with two
screws.(4 locations in total).

2

Using an insert-hole-in- anchor, hang the
hanging bolt.

3

Install a hexagon nut and a flat washer
(locally-procured)to the hanging bolt as
shown in the figure in the left, and lift the
main unit to hang on the hanger metal.

4

After checking with a level that the unit is
level, tighten the hexagon nut.

* The tilt of the unit should be within ±5°

in front/back and left/right.

Procedure

1

Fix the furnished hanger metal with two
screws. (3 locations in total).

2

After checking with a level that the unit is level,
fix the unit with the furnished wood screws.

* The tilt of the unit should be within ±5° in

front/back and left/right.

* Block up the parts of hanger holes (2 places)

by using insulation PE after installing the hang-
er.

Screws(M5)

Screws(M5)
(locally procude)

(locally procude)

Screws(M5)
(locally procude)

PE

PE

B

D unit

Six-sided Nut

Six-sided Nut
(M10 or M

8

)

(M10 or M

8

)

Six-sided Nut
(M10 or M

8

)

Hanger metal

Hanger metal

Hanger metal

Flat washer

Flat washer

Flat washer

Hanging bolt

Hanging bolt

Hanging bolt
(M10 or M

8

)

15,00

NOTE

!

• This unit has two different installation

types: (1) Ceiling-suspended type and
(2) wall-mounted type.

• Choose the proper installation pattern

according to the location of installation.

• The installation location for printed

wiring board can be changed.
Follow the procedure specified in the
"CONNECTING THE WIRING" section to
change the location.

• Once a screw-hole on the main unit has

had a screw hammered in, make sure
to either hammer it again or cover it
with alumium tape. (This is to prevent
condensation)

• Be sure to install the unit with the ceil-

ing-side up.

• Do not install near bedrooms. the

sound of refrigerant flowing through the
piping may sometimes be audible.

CAUTION

!

Ceiling-suspended type

Wall-mounted type

Installation of The Main Unit

«
...
20
21
22
23
24
...
»

Содержание A3UQ24GFD0








































Отзывы:

Нет отзывов

Похожие инструкции для A3UQ24GFD0

Бренд: GE Страницы: 72

Бренд: Haier Страницы: 122

Бренд: QuietFlo Страницы: 24

Бренд: Zibro Страницы: 2

Бренд: TruSens Страницы: 32

Бренд: DCG Страницы: 18

Softaire RERV-80

Бренд: Air Specialties Страницы: 16

Бренд: EarthLinked Страницы: 11

Бренд: Turbo Air Страницы: 21

Бренд: MAXA Страницы: 44

Бренд: Kogan Страницы: 17

Бренд: Salda Страницы: 14

Бренд: Kaysun Страницы: 16

Бренд: Daewoo Страницы: 41

Бренд: Hitecsa Страницы: 19

Бренд: ACPro Страницы: 41

TAC-07CHSA/XA71

Бренд: TCL Страницы: 41

Бренд: Dadam micro Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды