LG 50PC1DR - - 50" Plasma TV Скачать руководство пользователя страница 95

Страница: 95 / 138

SOFTWARE UPDATES

Plasma Training

Software Updates

If the update is sucessful the display will appear as below:

This light will blink
during update and
become solid when
done if successful.

OK will be displayed
after Verify is completed.

• Switch the TV OFF and remove AC power.

• Switch the jig OFF and remove AC power.

• Remove the cable from the jig to the control PCB from P101 on the PCB.

• Reconnect P151 Y-SUS, P151 Z-SUS, P100 and P204 on the tuner PCB make sure AC cables are
firmly connected to the AC switch and SMPS connectors are seated and all cables are in their
retainers.

• Remount Digital/Tuner PCB mount assembly to the TV.

Содержание 50PC1DR - - 50" Plasma TV










































































































































Результаты поиска

Содержание 50PC1DR - - 50" Plasma TV

Отзывы:

Похожие инструкции для 50PC1DR - - 50" Plasma TV

Бренды по названию

Популярные бренды

LG 50PC1DR - - 50" Plasma TV, Руководство по обучению

Результаты поиска

Содержание 50PC1DR - - 50" Plasma TV

Отзывы:

Похожие инструкции для 50PC1DR - - 50" Plasma TV

Бренды по названию

Популярные бренды