LG 50PC1DR - - 50" Plasma TV Скачать руководство пользователя страница 93

Страница: 93 / 138

SOFTWARE UPDATES

Plasma Training

Software Updates

File location

Panel model

Rom version

File location

Panel model

Rom version

The File location will not appear on the label on the control PCB.

• Turn the power to the jig ON

• Use the MODEL up or down to select the correct file.

*To use the MODEL up/down keys. Press either key for 3 seconds and release the key, you will see

the model id disappear and only the number will be shown in the upper left.

*Quickly use the up/down keys to scroll to the file in location number 1. The file will load after a

few seconds. The file name (42X2DN05B) appears in the screen on the jig.

NOTE: To use any key on the jig you must hold the key down for at least 3 seconds.

•Apply AC power to the jig with the switch on the jig OFF and apply AC

to the TV. Only one LED will be lit.

•Press the main AC power switch to the ON position on the TV. These

additional LED’s will be lit. If the TV is in the ON state when you connect
AC, the unit will turn itself on. Turn on the jig.

Digital PCB

Содержание 50PC1DR - - 50" Plasma TV










































































































































Результаты поиска

Содержание 50PC1DR - - 50" Plasma TV

Отзывы:

Похожие инструкции для 50PC1DR - - 50" Plasma TV

Бренды по названию

Популярные бренды

LG 50PC1DR - - 50" Plasma TV, Руководство по обучению

Результаты поиска

Содержание 50PC1DR - - 50" Plasma TV

Отзывы:

Похожие инструкции для 50PC1DR - - 50" Plasma TV

Бренды по названию

Популярные бренды