LG 49MS75A Скачать руководство пользователя страница 9

Страница: 9 / 58

- 9 -

LGE Internal Use Only

Only for training and service purposes

4.3. LAN Inspection

4.3.1. Equipment & Condition

▪ Each other connection to LAN Port of IP Hub and Jig

4.3.2. LAN inspection solution

1) LAN Port connection with PCB

2) Network setting at MENU Mode of SET (Installer Menu →

119 → 253 → Menu)

3) Setting automatic IP

4) Setting state confirmation

→ If automatic setting is finished, you confirm IP and MAC

Address.

4.4. LAN PORT INSPECTION(PING TEST)

4.4.1. Equipment setting

1) Play the LAN Port Test PROGRAM.

2) Input IP set up for an inspection to Test Program.

*IP Number : 12.12.2.2

4.4.2. LAN PORT inspection(PING TEST)

1) Play the LAN Port Test Program.

2) Connect each other LAN Port Jack.

3) Play Test (F9) button and confirm OK Message.

4) Remove LAN cable.

4.5 Serial number download

Connect Bar Code scan equipment and set by RS-232C

cable.

1) E2PROM Data Write

2) E2PROM Data Read

4.6 EDID/DDC Download (EDID PCM)

4.6.1 Overview

It is a VESA regulation. A PC or a MNT will display an optimal

resolution through information sharing without any necessity

of user input. It is a realization of “Plug and Play”.

4.6.2 Equipment

1) Since EDID data is embedded, EDID download JIG, HDMI

cable and D-sub are not need.

2) Adjust by using remote controller.

4.6.3 Download method

1) Press Adj. key on the Adj. R/C,

2) Select EDID D/L (PCM) menu.

3) By pressing Enter key, EDID download will begin

4) If Download is successful, OK is display, but If Download is

failure, NG is displayed.

5) If Download is failure, Re-try downloads.

→ Caution) When EDID Download, must remove HDMI / D-

sub Cable.

4.6.4. EDID DATA

1) DVI (Check Sum : 0x3C)

Содержание 49MS75A




















































Результаты поиска

Содержание 49MS75A

Отзывы:

Похожие инструкции для 49MS75A

Бренды по названию

Популярные бренды

LG 49MS75A, Руководство по обслуживанию

Результаты поиска

Содержание 49MS75A

Отзывы:

Похожие инструкции для 49MS75A

Бренды по названию

Популярные бренды