39
206-4325
102 - ATSC BAND
Selects the RF band used by the ATSC tuner:
0 = Broadcast
1 = Cable
2 = HRC
3 = IRC
4 = Same as NTSC (default)
103 - ATSC TUNE MODE
Sets the ATSC tuning mode. Default set to 1 for Physical Channel
tuning. Set to 0 for Virtual Channel tuning.
104 - START MINOR CHANNEL
When a digital (ATSC)
Start Channel has been specified for item
004 STRT CHANNEL, this item sets the Minor Start Channel
number. Set to 0 when an analog (NTSC) Start Channel has been
specified for item 004.
Note:
This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 0 or 255.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 0 to use the default aspect ratio each time the TV is turned
ON (see item 096 DEF. ASP. RATIO). If set to 1, the aspect ratio
set before the TV was turned OFF will be the current aspect ratio
when the TV is turned ON again.
107 - BANNER SELECT
Selects the type of banner to display during channel change.
Set to 1 for channel label display, plus channel information (full
banner). Set to 0 for channel label display only (small banner).
116 - VIDEO MUTE EN (Video Mute Enable)
Applicable for analog channels only. If set to 1, video mutes (blank
screen) when no signal is present.
117 - FACT DEFAULT (Factory Default)
Set to 1 and press OK to restore the factory default settings of all
Installer Menu items. Once complete, the value returns to 0.
Caution:
If set to 1, this clears all Installer Menu custom
settings and restores the factory default settings. It also
clears the channel lineup, including any assigned
channel icons and custom text labels.
Note:
See also Reference section, “Restoring Factory Defaults on
the TV(s),” for further information.
118 - POWER SAVINGS
Default set to 3—the power circuitry for both the embedded
b
-LAN
module and the GAME CONTROL/MPI port is only powered when
the TV is turned ON. When the TV is turned OFF, the embedded
b
-LAN and the GAME CONTROL/MPI port are not powered.
Note that the TV must be turned ON in order to communicate with
the embedded
b
-LAN module for configuration and control when
POWER SAVINGS is set to 3. If POWER SAVINGS is set to 1, the
b
-LAN module is always powered.
Similarly, if MPI communication is required for external MPI
control, POWER SAVINGS should be set to 1 so that the GAME
CONTROL/MPI port circuitry is always powered.
Note:
See Reference section, “
b
-LAN Setup & Overview,” for
further information.
Caution: POWER SAVINGS should NEVER be set to 7.
This setting is intended for factory use only.
119 - DATA CHANNEL
Set to 0 to disable. Set from 1 to 135 to match the RF channel
number that will be used by the Pro:Centric server as its data
channel. *
For TVs in Pass-through Mode or FTG Mode via CPU, if this item
is left at its default value (255), the TV’s Data Channel Auto Search
feature will be enabled (see additional information below).
Note:
The Data Channel Auto Search feature is not available
when the TV’s EBL is in FTG Mode. If the DATA CHANNEL value
is 255 when the TV is configured for FTG Mode via EBL, DATA
CHANNEL is defaulted to 0.
Data Channel Auto Search feature: When this item is set to 255
(default), once every 24 hours, the TV will initiate a search of 10
predefined channels (10, 20, 30, ... 100) and then, if necessary,
perform a complete search of the RF channels (1 to 135) in an
attempt to find the RF channel used by the Pro:Centric server as
its data channel. If the Pro:Centric RF channel is found, the DATA
CHANNEL value will be changed from 255 to match the server’s
RF channel number. The time at which the Auto Search occurs
depends on the setting of item 121 P:C RF WAKE HR. See item
121 description for further information.
Note:
Pro:Centric updates are downloaded from the Pro:Centric
server to the TV when the TV is turned OFF. While Pro:Centric
updates are in progress, it is not possible to turn ON the TV.
Note:
The Data Channel is automatically set to “253” if Media
Type is set to “IP” either in the EZ-Manager Wizard or in the IP
Environment / Pro:Centric Menu on the TV (see “EZ-Manager
Wizard” on pages 16 to 25 or “Pro:Centric Setup” on pages 59 to
61, respectively) or if Installer Menu item #119 Data Channel is
set to “IP Address” or “IP Domain Name” in the Cloud Configuration
Tool, which is typically used to configure TV CPUs for FTG Mode
operation. It is not possible to change the value to “253” directly in
the Installer Menu.
Installer Menu (Cont.)
*
PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.
