LG 29LN300B, Руководство по обслуживанию

Страница: 12 / 33

- 12 - LGE Internal Use Only
Copyright © LG Electronics. Inc. All right reserved.
Only for training and service purposes
4.4. White balance adjustment
-Equipment
1) Color Analyzer: CA-210 (LED Module : CH 14)
2) Adj. Computer(During auto adj., RS-232C protocol is
needed)
3) Adjust Remocon
RGB_Gains are fixed data for each model.
Insert RS-232C Jack which is connected with PC for White
Balance or equivalent device.
* Total Assembly line should be check whether the color
coordinate(x,y) data refer to below table were meet or not.
*Note : x,y coordinates are drifted about 0.007 after 30 mins
heat-run. So checking color coordinate within 5-min at
total assembly line, consider x,y coordinates might be
up to 0.007 than x,y target of each color temperature.
*Note : Manual W/B process using adjusts Remote control.
1) After enter Service Mode by pushing "ADJ" key,
2) Enter "White Balance" by pushing "►" key at "White Bal-
ance".
* When doing Adjustment, Please make circumstance as
below.
4.5. DPM Operation check
■ Measurement Condition: 100~240V@ 50/60Hz
1) Set Input to RGB-PC and connect D-sub cable to set –
RGB Mode. Set Input to HDMI(with Input Label set to PC)
and connect HDMI cable to set – HDMI Mode
2) Cut off H sync or V sync of signal.
3) Check DPM operation refer to the below table.
4.6. Model Name & SW Version & Adjust
check.
* Press the ‘Instart’ key of ADJ remote controller
4.6.1. Model Name& SW Version Check
1) Check ‘Model Name’.
2) Check ‘S/W Version’ (Refer to the IC Ver. in the BOM)
4.6.2. Adjust Check
1) Check ‘Country Group’
2) Check ‘Area Option’
3) Check ‘Tool Option’ (Refer to the BOM Comments)
4) Check ‘Adjust ADC[Comp&RGB]’ is OK.
5) Check ‘EDID[RGB&HDMI]’ is OK.
* After check all, Press the 'EXIT' key of ADJ remote controller
to go out SVC menu.
4.7. Outgoing condition Configuration
* After all function test., press IN-STOP Key by SVC Remote
controller. And make Outgoing Condition
~›ŒGiˆ“ˆ•ŠŒG
j–“–™G{Œ”—UG ඔG j––“G ඖG
yTnˆ•G G XWWG G
nTnˆ•G G XW[G G
iTnˆ•G G X`YG G
yTjœ›G G ][G G
nTjœ›G G ][G G
iTjœ›G G ][G G
{Œš›Twˆ››Œ™•G G vuG G
iˆŠ’“Ž›G G XWWG G
yŒšŒ›G G {–GzŒ›G G
G
WUG{––“Gv—›–•XG G G
XUG{––“Gv—›–•YG G G
YUG{––“Gv—›–•ZG G G
ZUG{––“Gv—›–•[G G G
[UG{––“Gv—›–•\G G G
\UG{––“Gv—›–•]G
]UGj–œ•›™ Gn™–œ—G
G G
^UGhkjGjˆ“‰™ˆ›–•G G G
_UG~›ŒGiˆ“ˆ•ŠŒG ඖ G G
`UGXWGw–•›G~iG G G G
XWUG{Œš›Gwˆ››Œ™•G G G G G
XXUGlkpkGkVsG G G
XYUGzœ‰GiVjG
XZUG{–œŠGzŒ•š›› GzŒ››•ŽG
X[UGlŸ›UGp•—œ›Gh‹‘œš›G
X\UGzwrGs—š •ŠGh‹‘œš›G
X]UzwkpmGs—š •ŠGh‹‘œš›G
G G
G G G
Operating Condition Sync
(H/V)
Video LED
(SET)
Wattage
(W)
Power S/W On Sleep mode -
RGB,HDMI
Off/Off Off Amber 1
Color
Temperature
Cool 13,000k °K X=0.276 (±0.03)
Y=0.275 (±0.03)
<Test Signal>
Inner pattern
(204gray,80IRE)
Medium 9,300k °K X=0.290 (±0.03)
Y=0.298 (±0.03)
Warm 6,500k °K X=0.318 (±0.03)
Y=0.334 (±0.03)
Luminance
(cd/m²)
Cool Min : 80 Typ : 110 <Test Signal>
Inner pattern
(204gray,80IRE)
Medium Min : 80 Typ : 110
Warm Min : 70 Typ : 110