background image

7

ENG

ENGLISH

7

EXTERNAL CONTROL DEVICE SETUP

* Commands may work differently depending on model and signal.

01. Power (Command: k a)

 

► To control Power *On or Off of the set.

Transmission[k][a][  ][Set ID][  ][Data][Cr]

Data 00 : Power Off 

01 : *Power On

Ack [a][ ][Set ID][ ][OK/NG][Data][x]

 

► To Show TV is Power On or *Off

Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK][Data][x]

*  Similarly, if other functions transmit ‘FF’ data 

based on this format, Acknowledgement feedback 

presents status about each function.

02. Aspect Ratio (Command: k c) 

(Main Picture Size)

 

► To adjust the screen format. (Main picture format) 

You can also adjust the screen format using the 

Aspect Ratio in the Q.MENU. or PICTURE menu.

Transmission [k][c][ ][Set ID][ ][Data][Cr]

Data 01 :  Normal screen 

(4:3)

 

02 :  Wide screen 

(16:9)

 

04 : Zoom

 

05 : Zoom 2

 

 (Latin  America 

except Colombia 

Only)

 

06 :  Set by Program/ 

Original

07 : 14:9

(Europe, Colombia, Mid-East, 

Asia except South Korea and 

Japan)

09 : * Just Scan

0B : Full Wide

(Europe, Colombia, Mid-

East, Asia except South 

Korea and Japan)

10 to 1F :  Cinema Zoom 1 to 16

0c : 21:9 (Depending on model)

Ack [c][ ][Set ID][ ][OK/NG][Data][x]

*  Using the PC input, you select either 16:9 or 4:3 

screen aspect ratio.

*  In DTV/HDMI/Component mode (high-definition), 

Just Scan is available.

*  Full wide mode may work differently based on 

model and is supported for DTV fully, and ATV, 

AV partially.

03. Screen Mute (Command: k d)

 

► To select screen mute on/off.

Transmission [k][d][ ][Set ID][ ][Data][Cr]

Data 00 :  Screen mute off (Picture on) 

Video mute off

 

01 :  Screen mute on (Picture off)

 

10 : Video mute on

Ack [d][ ][Set ID][ ][OK/NG][Data][x]

*  In case of video mute on only, TV will display On 

Screen Display(OSD). But, in case of Screen mute 

on, TV will not display OSD.

04. Volume Mute (Command: k e)

 

► To control volume mute on/off. 

You can also adjust mute using the MUTE button 

on remote control.

Transmission [k][e][ ][Set ID][ ][Data][Cr]

Data 00 :  Volume mute on (Volume off)

 

01 :  Volume mute off (Volume on)

Ack [e][ ][Set ID][ ][OK/NG][Data][x]

05. Volume Control (Command: k f)

 

► To adjust volume. 

You can also adjust volume with the volume 

buttons on remote control.

Transmission [k][f][ ][Set ID][ ][Data][Cr]

Data Min :  00 to Max : 64

Ack [f][ ][Set ID][ ][OK/NG][Data][x]

06. Contrast (Command: k g)

 

► To adjust screen contrast. 

You can also adjust contrast in the PICTURE 

menu.

Transmission [k][g][ ][Set ID][ ][Data][Cr]

Data Min :  00 to Max : 64

Ack [g][ ][Set ID][ ][OK/NG][Data][x]

07. Brightness (Command: k h)

 

► To adjust screen brightness. 

You can also adjust brightness in the PICTURE 

menu.

Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data Min :  00 to Max : 64

Ack [h][ ][Set ID][ ][OK/NG][Data][x]

08. Color/Colour (Command: k i)

 

► To adjust the screen Color(Colour). 

You can also adjust colour in the PICTURE menu.

Transmission [k][i][ ][Set ID][ ][Data][Cr]

Содержание OLED65G6P















































Отзывы: