LG-Nortel Aria 130 Скачать руководство пользователя

Страница: 72 / 81

Aria 130c/130/300/600 DECT
Wireless Terminal (GDC-345H) User Guide

LG-Nortel systems

６８

Issue

2.3

7. TROUBLESHOOTING GUIDE

Problem

Reason

Solution

LCD is empty.

No power

Check the battery then, press the

[PWR]

button.

“

NO CHANNEL

” is displayed

when pressing

[ON/OFF]

button.

No free channel

Wait until a free channel is released.

Small Voice

Small voice level

While connected to a call,

Press

( ) button.

Small Ring

Small ring volume level

Adjust Ring volume level;

Refer to ‘

HS Setting

’.

“

UNREGISTERED

” is displayed

on the LCD.

Not subscribed

Subscribe the terminal.

Refer to ‘6.2 Subscription’.

Low battery icon( ) is
flashing on LCD with warning
tone.

Low battery level

Recharge the battery.

Power-off right after power-on

Almost fully
discharged battery

Recharge the battery.

No Base Lock State

Wait until Base Locked or move to a
place with good RSSI

No tone is heard when pressing
a digit.

Tone Volume is off

Adjust Key tone level;

In an idle state

Refer to ‘

HS Setting

’

Unexpected call disconnect or
call failure

Bad radio
Environment

Radio environment is changed
unexpectedly even in the same place.
Move to another place with good RSSI
or wait until RSSI is recovered.

Different battery duration from
the battery duration table

Bad charging habit or kept
the battery inadequate
place.

Charge and keep the battery
according to the suggested ways.

Refer to ‘3. Maintenance’.

Subscript can’t be done.

1. There is interference of

other systems with

subscription.
2. A station is too far from

the terminal.

3. Wrong PARK value or
(and) wrong AC code
4. There is no available
wireless channel.

1. Remove other systems.
2. Be sure a batation is close to the

terminal.

3. Be sure PARK value and AC
code are correct.

4. Wait unan available wireless

channel is free. If the subscription

still fails, retry of the power reset.

When pressing

TALK

button,

Phone icon

( ) is blinking

several times and disappeared.

Subscription Disagreement

Do desubscribe locally in both sides,
the system and the terminal and
subscribe the terminal in the system
again.

When pressing

TALK

button,

nothing is happened.

Out of Range

1. Be sure the terminal is locked to a

base station.

2. Be sure the system is operating

properly.

RSSI : Radio Signal Strength Indication. Always a user can see RSSI icon while the terminal is operating.

Содержание Aria 130


















































































Результаты поиска

Содержание Aria 130

Отзывы:

Похожие инструкции для Aria 130

Бренды по названию

Популярные бренды

LG-Nortel Aria 130, Руководство пользователя

Результаты поиска

Содержание Aria 130

Отзывы:

Похожие инструкции для Aria 130

Бренды по названию

Популярные бренды