background image

GA300553102_002_C2 

– 04/2017

 

 

7

 

 

3. 

Installation 

3.1 

Mechanical Installation 

 

The GRAPHIX CONTROLLER can be used as follows: 

 

  Rack installation  

  Front panel cut-out installation  

  Benchtop instrument 

 

 

WARNING: Powering down 

Install the instrument or place it so that you are in  a position to operate the 
mains  power  switch  at  any  time  or  to  ensure  that  the  instrument  can  be 
deenergised at any time. 
 

 

3.2 

Connections 

Figure 1, page 7 depicts the connection options on the rear of the GRAPHIX controller. 

 

 

Figure 1 

– 

Rear of the instrument 

 

Mains power connection with mains switch 
and instrument fuses 

Earth connection 

C1/C2  Connection of measurement channel 1 for 

sensors  (CH1 A und CH1 B) 

D1/D2  Connection of measurement channel 2 (for 

GRAPHIX TWO and THREE only) for 
sensors  (CH2 A and CH2 B)  

E1/E2  Connection of measurement channel 3 (for 

GRAPHIX THREE only) for sensors (CH3 A 
and CH3 B)  

Relay output connection (Relay Output) 

Analogue output, chart recorder output and 
external control connection (Control)  

RS232 or RS485 interface connection 
(RS232 / RS485) 

 

 

 

CAUTION: Impermissible Sensors. 

Connecting  sensors  which  have  not  been  designed  to  be  operated  in 
connection with the GRAPHIX controller or which do not comply with current 
EMC  guidelines  can  impair  operation  of  the  instrument  or  even  damage  it. 
Always  operate  the  GRAPHIX  controller  with  approved  sensors. 



 Chapter 1.2 

 Conforming Utilisation, page 4. 

 

 

CAUTION: Multiple Sensors. 

Only  a  single  sensor  may  be  connected  to  each  measurement  channel. 
Otherwise  the  connected  sensors  will  suffer  damage.  Connect  to  each 
measurement channel precisely one sensor only. 

 
 
 

Содержание 230680V01





















Отзывы: