Lexmark 2070 Color Jetprinter Скачать руководство пользователя страница 39

Страница: 39 / 78

Repair Information 4-7

4090-001

Exit Drive Belt Removal

1. Remove the front cover.

2. Remove the rear cover.

3. Remove the carrier frame assembly.

4. Remove the paper load door and manual insert tray.

5. Remove the small feed roll shaft.

6. Unlatch the left side of the exit roller shaft and work the belt off

the exit roller pulley.

7. Pull up the four clips securing the mid frame to the large feed

roll and work the mid frame out of both side frames.

8. Spread the right side frame apart far enough to allow removal of

the exit drive belt.

Exit Roller Removal

1. Remove the front cover.

2. Remove the two screws from the star roller assembly and

remove the assembly.

3. Unlatch the left side of the exit roller and remove the exit drive

belt from the exit roller pulley.

4. Remove the exit roller.

Feed Arm Assembly Removal

1. Remove the front cover.

2. Remove the rear cover.

3. Remove the C-clip from the feed arm and remove the assembly.

Содержание 2070 Color Jetprinter















































































Результаты поиска

Содержание 2070 Color Jetprinter

Отзывы:

Похожие инструкции для 2070 Color Jetprinter

Бренды по названию

Популярные бренды

Lexmark 2070 Color Jetprinter, Руководство по обслуживанию

Результаты поиска

Содержание 2070 Color Jetprinter

Отзывы:

Похожие инструкции для 2070 Color Jetprinter

Бренды по названию

Популярные бренды