background image

���

MODEL: ASHTON AI42DV

LEXINGTON FORGE 

DIRECT VENT GAS INSERT

INSTALLATION AND OPERATING INSTRUCTIONS

 

WARNINGS

IF THE INFORMATION IN THESE INSTRUCTIONS ARE 
NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION 
MAY  RESULT  CAUSING  PROPERTY  DAMAGE, 
PERSONAL INJURY OR LOSS OF LIFE.

–    Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 
other appliance.

–    WHAT TO DO IF YOU SMELL GAS
      • Do not try to light any appliance.
      • Do not touch any electrical switch; do not use 

any phone in your building.

      • Immediately  call  your  gas  supplier  from  a 

neighbor's  phone.  Follow  the  gas  supplier's 
instructions.

      • If you cannot reach your gas supplier, call the 

fire department.

–    Installation  and  service  must  be  performed 

by  a  qualified  installer,  service  agency  or  the 
gas supplier.

WARNING:  Improper  installation,  adjustment, 
alteration, services or maintenance can cause injury or 
property damage. Refer to this manual. For assistance 
or additional information consult a qualified installer, 
service agency or the gas supplier.   

This appliance is only for use with the type of gas 
indicated  on  the  rating  plate. This  appliance  is 
not  convertible  for  use  with  other  gases,  unless  a 
certified kit is used. 
This appliance may be installed in an aftermarket*, 
permanently located, manufactured home, where not 
prohibited by local codes.

*Aftermarket: Completion of sale, not for purpose of resale, from 
the manufacturer. 

DUE TO  HIGH TEMPERATURES, THE 
APPLIANCE  SHOULD  BE  LOCATED 
OUT  OF TRAFFIC  AND  AWAY  FROM 
FURNITURE AND DRAPERIES.

CHILDREN  AND  ADULTS  SHOULD  BE 
ALERTED TO THE  HAZARDS  OF  HIGH 
SURFACE TEMPERATURE AND SHOULD 
STAY  AWAY  TO  AVOID  BURNS  OR 
CLOTHING IGNITION.

YOUNG  CHILDREN  SHOULD  BE 
SUPERVISED WHEN THEY  ARE  IN THE 
SAME ROOM AS THE APPLIANCE.

CLOTHING  OR  OTHER  FLAMMABLE 
MATERIAL  SHOULD  NOT  BE  PLACED 
ON OR NEAR THE APPLIANCE.

KEEP THE  ROOM  AREA  CLEAR  AND 
FREE FROM COMBUSTIBLE MATERIALS, 
GASOLINE,  AND  OTHER  FLAMMABLE 
VAPORS AND LIQUIDS.

READ BEFORE INSTALLING. SAVE THESE INSTRUCTIONS

Содержание ASHTON AI42DV









































Отзывы: