manualshive.com logo in svg

Lexicomm ViLX-228, Руководство по установке и пусконаладке

Поделиться
Скачать
Lexicomm ViLX-228 Скачать руководство пользователя страница 12

 

 

 

Document PViLX228 7001-06 Rev 6 2017 

Page 12 of 24 

 

5.8

 

Auxiliary Connections 

The ViLX-228 Master Station has three auxiliary connections: 

 

Fault is a normally closed volt free relay (30V DC 1A) which 

OPENS on any fault, including loss of power. 

 

In Use is a normally open volt free relay (30V DC 1A) connection 

which closes when any outstation is operated, see Remote Signal 

Display section 7.6 switch settings for further information. 

 

Enable is a normally CLOSED input, and is required to operate the 

system.  If Jumper J1 is in place, then no connection is required at 

the terminals. This function only disables Type B outstations, with Type A outstations and “Assist Call” 

emergency assistance alarm systems continuing to operate. It is advised that this feature is not used as 

the system should be available at all times, not just during an evacuation. If the feature is used then 

the mode LED illuminates yellow after 30 seconds to show that the system is disabled. 

 

 

5.9

 

Powering up procedure 

To power up the ViLX-228 Master Station, carefully check all internal wiring before applying mains 

power to the ViLX-228 Master Station.  Once the ViLX-228 Master Station is powered, the battery can be 

attached using the battery leads supplied.  When attaching the battery, always attach the Positive 

(Red+) terminal first. 

 

5.10

 

Powering down procedure 

To power down the ViLX-228 Master Station, first disconnect the battery.  Always disconnect the 

Negative (Black -) terminal first.  Once the battery leads have been disconnected, then remove mains 

power. 

Содержание ViLX-228

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды