Levitronix 100-91405 Скачать руководство пользователя страница 19

Страница: 19 / 25

User Manual for BPS-i600

www.levitronix.com

PL-4089-00, Rev00, DCO# 21-271

4.1.6 Installation of RS485 Fieldbus Multi-Pump System Arrays

Figure 16

shows a multi-pump system arrangement with the

RS485

fieldbus and its basic specifications.

Figure 16: Multi-pump system arrangement with RS485 fieldbus

Following points and information shall be considered:

➔

Testing has been done with arrangements of 8 pump systems. Higher number is possible but it is
recommended to contact

Levitronix

Technical Service

department (see

Section 8

) for details and support.

➔

Address setting of the pump units can be done with the

Levitronix

Service Software

and a

PC. A USB/RS485

converter cable with integrated initialization network can be ordered according to

Table 3.

➔

The

RS485

protocol for master communication is available at

Levitronix

on request.

➔

Do not use multiple master systems at the same time.

➔

Do not use closed ring arrangements.

4.2 Mechanical Installation

4.2.1 Mechanical Installation of Driver and Pump Head

The driver can be fixed with four screws on the motor feet (see

Figure 7

). Mounting can be done in either in

horizontal or vertical position. When mounting the pump head fittings into a circuit, care shall be taken that no
mechanical stress is acting on the fittings, which can result in distorting creeping effects.

WARNING

BPS-i600 pump drivers are not rated to be placed next to flammable
gases. Do not use the driver next to flammable gases.

4.2.2 Mechanical Installation of Water Cooling Module

The water cooling module

WCM-600.1

can be mounted to the driver top as illustrated in

Figure 8

. The cooling

liquid (for example water) can be connected over the two NPT 1/8” fittings (see

Figure 8

). A minimum cooling

liquid flow of 0.5 l/min at @

≤ 20°C temperature is recommended.

120

510

Master

Integrated

System

Integrated

System

Integrated

System

Branch Bus Lines:

Length sum of all < 33m.

Main Bus Line: < 100m

Shielded cable with drilled wires recommended.

Termination:

Recommended for main bus line Length > 5m.

Initialization Network:

Always recommended.

To be implemented at the master.

Содержание 100-91405


























Результаты поиска

Содержание 100-91405

Отзывы:

Похожие инструкции для 100-91405

Бренды по названию

Популярные бренды

Levitronix 100-91405, Руководство пользователя

Результаты поиска

Содержание 100-91405

Отзывы:

Похожие инструкции для 100-91405

Бренды по названию

Популярные бренды