5
IT
PL
PT
RU
TR
Sensore
Czujnik
Sensor
Датчик
Sensör
1
Sportello dello
scomparto batterie
Pokrywa komory
baterii
Tampa do
compartimento das
pilhas
Крышка
батарейного отсека
Pil bölmesi kapağı
2
Scomparto batterie Komora baterii
Compartimento das
pilhas
Батарейный отсек Pil bölmesi
3
Pulsante
RESET
(Reimposta)
Przycisk
RESET
(Resetowanie)
Botão
RESET
(Repor)
Кнопка
RESET
(Сброс)
RESET
(Sıfırla)
düğmesi
4
Interruttore dei
canali (1–3)
Przełącznik
kanałów (1–3)
Seletor de canais
(1–3)
Переключатель
каналов (1–3)
Kanal düğmesi (1–3)
5
Indicatore LED
Wskaźnik LED
Indicador LED
Светодиодный
индикатор
LED gösterge
EN
Levenhuk Wezzer Teo TH40 Thermohygrometer
The kit includes:
base station, sensor, USB cable, user manual, and warranty.
Getting started
Base station
•
Connect the power cable to the device and connect the DC adapter to the AC power supply; or
•
Open the battery compartment cover (18) and insert 3 AA batteries according to the correct polarity. Close the cover.
•
Once the batteries are installed, the base station will search for the outdoor units for the first 5 minutes. After that, the base
station can be manually set to receive. To do this, press the
CH
button, and then press this button again to choose between
channels 1, 2, or 3.
Sensor
•
Open the battery compartment cover (2). Insert 2 AAA batteries according to the correct polarity.
•
Set the desired channel with the switch (4). Close the cover.
NOTE!
This weather station can be operated with up to 3 remote sensors. Each remote sensor that is to be connected must be
operated on a different channel. If only one remote sensor is connected, it should be operated on channel 1.
•
To re-establish the sensor connection manually, press
RESET
using a pin.
Sensor connection
•
Place the base station and the remote sensor within the effective transmission range. Ensure that the channels are assigned after
you set up the power supply for the base station and all the sensors.
•
If the reception is successful, the display will show the temperature and humidity of the respective outdoor sensor. If the values
are not received from a channel, "—" appears on the display. Check the batteries and try it again. Check if there is any source of
interference.
•
When changing batteries, replace the batteries first in the base unit, and then in all the sensors, to re-establish the connection. If
an adapter supplies power to any of the devices, briefly disconnect the power to that device when replacing the batteries. If you
change the batteries only in one of the devices (for example, in the sensor), the signal may not be received correctly.
•
The effective range may differ depending on the unit’s position. Due to interference (various remote control devices, etc.), the
maximum distance between the base unit and the sensor may be significantly reduced. In such cases, we suggest moving the
base unit and sensor a little. Sometimes it is enough to move one of these units a few inches!
NOTE!
Although the sensor is weather resistant, never place it in direct sunlight or in the rain or snow.
Time setting
Press the
MODE
button and hold it for 3 seconds. The digits that are to be set are flashing. Press
UP
or
DOWN
to change the value,
and then press
MODE
to continue.
The setting order: 12/24h > Hours > Minutes > Year > Date/Month or Month/Date format > Month > Date > Weekday (7 languages).
Finally, press the
MODE
button to save the settings and exit.
