less care LBSDG3072 Скачать руководство пользователя страница 10

Страница: 10 / 21

www.lesscare.com

ULTRA-G

SHOWER DOORS • SHOWER ENCLOSURES

Clear Rubber
Gasket

Figure 7

Figure 8

Figure 6

Figure 9

Left Side Installation

Right Side Installation

3. Glass Door Installation

Install the Handle (07) onto the
Glass door (17).

IMPORTANT:

Make sure that

Clear

Rubber Gaskets

are in between the

Glass Door (17)

and knob; between

washer and glass; between

Cap and

Glass Door (17).

Then, tighten

Knob

and

Cap

by hand only. Do not use

any types of tools to tighten it

See Figure 9 for details.

4. Handle Installation

INSTALLATION STEPS

Disassemble the

Upper And Lower Pivot Assemblies (4/5)

. Mount the

Glass

Door (17)

into

Pivot Bodies (4C/5C)

(see page 5).

NOTE:

Use of soft wood shim is recommended to support

Glass door (17)

from the bottom, during installation and all adjustments and it will prevent

Glass Door (17)

from scratched on the bottom.

IMPORTANT:

Make sure that clear rubber

Gaskets (4E/5E)

are in between

the

Glass Door (17)

and the

Back Plates (4F/5F).

Then, fasten tight

Countersunk Screws M6x14 (4G/5G)

. Make sure parts (4D/5D) are in the

right position.

IMPORTANT:

Do not let any metal parts come into contact directly with glass,

which will damage the glass notches and cause scratches or damage to the

Glass Door (17)

and,

If ignored, could result in serious injury or death.

See Figure 7 (left side installation) and 8 (right side installation) for details.

ATTENTION!

Glass Door (17)

has

2 notches for the Pivot assemblies.
The deeper notch must be on the
upper pivot assembly. Shallower
notch must be on the bottom of

Glass Door (17)

See Figure 6

Deeper Notch

must be on top

Shallower Notch

must be on bottom

Clear Rubber
Gasket

Washer

Knob

Cap

Washer

Содержание LBSDG3072






















Результаты поиска

Содержание LBSDG3072

Отзывы:

less care LBSDG3072, Руководство по установке, Страница: 10 / 21

Результаты поиска

Содержание LBSDG3072

Отзывы: