5
Ref.
No.
Part No. Description
Qty.
1
010171
Retainer “C” Clip
1
2
018628
Nylon Washer, 1/4
6
3
030503
Deflector Arm Mount Spacer
1
4
035030
Offset Bracket Deflector
1
5
060029
Machine Screw, 1/4-20x2
2
6
060033
Flat Washer, 1/4”
1
7
060034
Operating Lever and Rubber
1
8
060036
Lock Nut, Nylon Insert, 1/4
8
9
060057
Machine Screw Pan Head, 1/4-20x7/8
6
10 060059
Hex Nut, 1/4-20
1
11 060071
Hex Lock Nut, 5/16-18
1
12 060072
Nut, Nylon Insert, 5/16-18
1
13 060073
Lock Washer, 5/16
1
14 061052
Cotter Pin, 1/8 x 1
1
15 061053
Flat Washer, 3/8
1
16 061066
Deflector Tube, Plastic Only
1
17
--
--
--
18
--
--
--
19 706251
Deflector Actuator Rod
1
20 706252
Lever Rod Deflector Bracket
1
21 706253
Tube Bracket Mount, Lever, Deflector
1
22 706254
Deflector Tube Mount
1
23 030418
Remote Bracket
1
8
1
7
23
9
2
8
14
12
19
9
11
15
13
20
8
8
22
9
9
5
3
2
6
10
9
16
8
4
2
2
21
NOTE: Adjust the friction at the
three deflector arm pivot points
by tightening the nuts and then
backing them off 1/8th turn. Ad-
just the friction at the operating
lever pivot so that it will hold its
position.
Mounting Instructions
1.
Install the deflector tube mount (ref. 22) onto the right
side of the spreader frame (from the inside) as shown.
2.
Install the tube bracket mount (ref. 21) to the right side
of the frame using appropriate hardware as shown.
a.
Install 1/4-20 x 2 (ref. 5) through frame plate using
spacer (ref. 3), washer (ref. 6), and tighten using 1/
4-20 nut (ref. 10).
b.
Install nylon washer (ref. 2), bracket mount (ref.21)
nylon washer (ref 2) and tighten nut (ref. 8) until
bracket mount (ref. 21) easily turns.
3.
Install offset bracket (ref. 4) onto deflector (ref.16)
a.
Slide Long end of offset bracket into slot on
deflector (ref.16)
b.
Install 1/4-20 screw (ref. 9) and tighten sub
assembly using 1/4-20 nut (ref. 8)
4.
Slide deflector subassembly onto deflector tube mount
(ref. 22)
a.
Install washer (ref. 15) onto deflector tube mount
and lock in place using cotter pin (ref. 14)
5.
Fasten offset bracket (ref. 4) to bracket mount (ref. 21)
using appropriate hardware.
a.
Install 1/4-20 screw (ref. 9) and tighten sub
assembly using 1/4-20 nut (ref. 8) until deflector (ref.
16) moves easily on deflector tube mount (ref. 22)
6.
Install lever rod bracket (ref. 20) to bracket mount (ref.
21).
a.
Install, making sure small flange of lever rod bracket
faces to the inside of the spreader, using
appropriate hardware.
7.
Install remote bracket (ref. 23) onto right side of upper
handle.
a.
Install using one 1/4-20 (ref. 5) and one 1/4-20 nut
(ref. 8)
8.
Install operating lever (ref. 7) using appropriate
hardware
9.
Install rod (ref. 19) into operating lever (ref. 7) and into
lever rod bracket (ref. 20)
10. Slide deflector up toward the bottom of the hopper as
far as it will go.
11. Place the operating lever (ref. 7) i the “OFF” position
and adjust the lock nut (ref. 11) so it is down against
the lever rod bracket (ref. 20).
a.
Tighten nylock nut (ref. 12) up against the underside
of the lever rod bracket (ref. 20)
Drill 9/32" Hole
Right Handle
9.5
The Optional Remote Deflector - Part No. 706250
