3
The Optional Remote Deflector — Part No. 035591
Mounting Instructions
Parts List
1.Remove the right rear bolt holding the hopper to the frame but save
the nut. Install a 1/4-20 x 2" pan head machine screw (Ref. 14), the
rubber pad (Ref. 21) and the deflector mounting bracket assembly
and replace the nut and tighten.
2.Remove the upper handle mounting bolt on the right side of the
spreader and discard. Note: Save the 1/4-20 nylock nut.
a.
Install a 1/4-20 x 2" pan head machine screw (Ref. 14) into
the handle mounting hole.
b.
Install and tighten a 1/4-20 nut (Ref. 15) onto the pan head
machine screw.
c.
Install one 1/4" nylon washer (Ref. 5).
d.
Fit the lower hole in the pivot link (Ref. 13) over the end of
the machine screw.
e.
Install the second 1/4" nylon washer (Ref. 5).
f.
Install a 1/4-20 nylock nut (Ref. 4) and tighten until snug.
3.Drill a 9/32" hole in the upper handle assembly. (See sketch below.)
4.Put the threaded end of the control rod (Ref. 8) through the lower
control linkage hole (Ref. 12) and install the jam nut (Ref. 1 1) but
do not tighten the nut at this time.
5.Install the control lever mounting bracket (Ref. 2) on the bottom
side of the handle assembly.
a.
Install a 1/4-20 x 1-1/4" pan head machine screw (Ref. 6)
down through the hole you drilled in the handle assembly.
b.
Fit the mounting bracket (Ref. 2) over this screw.
Install a 1/4-20 nylock nut (Ref. 4) and tighten.
6.Slide deflector up towards the bottom of the hopper as
far as it will go.
7.Place the control lever (Ref. 1 ) in the "OFF" position and
adjust the upper control rod nut (Ref. 9) so it is down
against the lower control linkage (Ref. 12). Now tighten
the jam nut (Ref. 11) up against the under side of the
control linkage.
Ref.
Item
No.
No.No.
Description Used
1
060034
Operating Leverand RubberHandle .......................... 1
2
030418
Bracket, Dual Lever ................................................. 1
3
060057
Machine Screw, 1/4-20 x 7/8 Pan Hd. ..................... 4
4
060036
Hex Nut, 1/4-20 Nylock ............................................ 6
5
082452
Flat Washer, 1/4 Nylon ........................................... 10
6
060047
Mach. Screw, 1/4-20 x 1-1/2 Pan Hd. ..................... 1
7
010171
Retainer, "C" Clip ...................................................... 1
8
035042
Threaded Rod, Deflector ......................................... 1
9
060071
Hex Nut. 5/16-18 ...................................................... 1
10
060073
Lock Washer. 5/16 ................................................... 1
11
060072
Hex Nut, 5/16-18 Nylock ......................................... 1
12
035041
Deflector Arm ............................................................ 1
13
035027
Flat Plate, Deflector .................................................. 1
14
060029
Machine Screw, 1/4-20 x 2 Pan Hd. ........................ 2
15
060059
Hex Nut.1/4-20 ......................................................... 1
16
082455
Offset Bracket .......................................................... 1
17
061066
Deflector Tube .......................................................... 1
18
061065
Deflector Bracket ..................................................... 1
19
061053
Flat Washer, 3/8 ....................................................... 1
20
061052
Cotter Pin, 1/8 x 1 ..................................................... 1
21
031851
Rubber Pad ............................................................... 1
8. The rods on the deflector
mounting bracket that the
deflector slides up and down
on should be lubricated with
a thin grease to keep dust
and dirt out of the openings.
NOTE: Adjust the friction at
the three deflector arm pivot
points by tightening the nuts
and then backing them off
1/8th turn. Adjust the friction
at the operating lever pivot
so that it will hold its position.
