Leroy-Somer CDC-START Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 58

Leroy-Somer CDC-START Скачать руководство пользователя страница 21

CDC - START
console

21

Remarks

Enter the mains supply nominal voltage.

Enter the rated speed of the motor given on its identification plate.

Enter the rated power of the motor given on its identification plate.

Enter the rated current of the motor given on its identification plate.

In % In : In Read mode, displays the current absorbed as a % of the motor rated current.

In Amps : In Read mode, displays the current absorbed in Amperes.

DISTANCE: Start/Stop control via terminal block contact.

LOCAL

: Control via Run and Stop/Reset keys on the console.

ON

: the STV 2313 restarts after a short mains loss of up to 1s.

OFF : the STV 2313 trips on mains loss fault.
Not to be used on applications with high resistive torque and low inertia.

Note : - indicates the part of the display where the adjustment is performed,

- indicates those menus which are only available with another option.

Remarks

If a code has been memorized, enter the code in order to access the parameters of menus 3
to 14. (See procedure in Section 3.5).

Remarks

Selects the communication language. All menus will be displayed in the selected language.
(See procedure in Section 3.4).

Page: 21

«
...
19
20
21
22
23
...
»

Содержание CDC-START



























































Отзывы:

Нет отзывов