Leonton PG5-1002-10GSFP-24 Series Скачать руководство пользователя страница 10

LED Indicators 

There  are  LED  light  indicators  located  on  the  front  panel  of  the  industrial  Ethernet  switch  that 
display the power status and network status. Each LED indicator has a different color and has its 
own specific meaning, see below in Table 2.1. 

LED 

Color 

Description 

P1 

Green 

On 

Power input 1 is active 

Off 

Power input 1 is inactive 

P2 

Green 

On 

Power input 2 is active 

Off 

Power input 2 is inactive 

STATUS 

Green 

On 

No configured event happens 

Red 

Off 

1. System booting  
2. Configured event happens 

MASTER 

Green 

On 

ERPS Owner Mode (Ring Master) is ready 

Off 

ERPS Owner Mode is not active 

RING 

Green 

On 

ERPS Ring Network is active and works well 

Flashing 

ERPS Ring works abnormally or misconfigure 

Off 

ERPS Ring Network is not active 

GE 

(LAN Port 1-8) 

Green 

 

On 

Connected to network, 10/100/1000Mbps 

Flashing 

Networking is active 

Off 

Not connected to network 

PoE 

(LAN Port 1-8) 

Green 

 

On 

Supplying power to the powered-device 

Off 

Not connected to a Powered Device 

L/A 

(SFP Port 9-10) 

Green 

On 

Connected to network, 10Gbps 

Flashing 

Networking is active 

Off 

Not connected to network 

Amber 

On 

Connected to network, 1000Mbps 

Flashing 

Networking is active 

Off 

Not connected to network 

 

Table 2.1: LED Indictors

 

Содержание PG5-1002-10GSFP-24 Series





















Отзывы: