Leonton MPT2-0201-M Series Скачать руководство пользователя страница 3

FCC Notice

 

This equipment has been tested and found to comply with the limits for a Class-A digital device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy. It may cause harmful interference to radio communications if the 
equipment is not installed and used in accordance with the instructions. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of 
the following measures:

 

 

Reorient or relocate the receiving antenna.

 

 

Increase the separation between the equipment and receiver.

 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 

is connected.

 

 

Consult the dealer or an experienced radio/TV technician for help.

 

 

 

Caution: Any changes or modifications not expressly approved by the grantee of this device could 
void the user's authority to operate the equipment.

 

 

 

CE Mark Warning

 

This is a Class-A product. In a domestic environment this product may cause radio interference in 
which case the user may be required to take adequate measures.

 

 

 

This document is the current official release manual. Please check our website (www.leonton.com) 
for any updated manual or contact us by e-mail ([email protected]).

 

Содержание MPT2-0201-M Series






















Отзывы: